782668
4
Zoom out
Zoom in
Previous page
1/20
Next page
Phone: 866-356-1992 | Email: Support@eccotemp.com | Address: 315 - A Industrial RD Summerville, SC 29483
PLEASE NOTE: THIS MANUAL IS SUBJECT TO CHANGE AT ANY TIME, TO ENSURE THIS MANUAL IS UP TO DATE PLEASE VISIT OUR HELP DESK
AT WWW.ECCOTEMP.COM FOR ALL OF OUR PRODUCT MANUALS.
Product Support: Eccotemp.com/help-desk Shop Online: Eccotemp.com/products Store Locater: Eccotemp.com/locater
WARNING
If your water heater requires a reset, be sure to TURN OFF THE BREAKERS prior to resetting the unit.
Resetting your unit without turning off the breakers can result in personal injury and damage to your
water heater.
WARNING! There is water contained in the coils of your water heater at all times. If your water heater
is exposed to freezing temperatures, the water in the coils could freeze, causing a break in the heat
exchanger of the unit, or the supply and return lines. This kind of damage will result in water running
freely into the space where the water heater is located, which can cause ooding. DO NOT install this
water heater where it may be subjected to a freeze. If your water heater is in an area where freezing is
a possibility, you must turn off the water to the heater and drain it of any water by disconnecting the
water lines. Leave the water lines disconnected until you intend to use the water heater.
Quick Start Guide
iE-18 | iE-24 | iE-27
1) Mounting
Mount vertically on a at surface (i.e. board or wall) larger than the unit itself. Make sure bracket is secure
by utilizing a stud or the provided wall anchors. Keep away from any potential splashing or leaking water and
strong magnetic elds.
2) Water connections
When installing your water connections make sure to use 3/4” NPT ttings. Please use the provided gaskets
to prevent leaks. When tightening ttings use a back-up wrench on inlet and outlet ttings (at sides of
ttings are located behind front cover). It is recommended to install a high pressure discharge valve and a
shut off valve on the incoming water line, in that order. Open a faucet and run water through the unit for a few
minutes to purge out air, turn off at faucet to build up pressure in the line to check for leaks.
3) Electrical connections
Wiring for electrical connection will differ depending on model please double check the model type on the
right side of the unit.
4) Operation
Unit is activated by the ow of water through the inlet. A desired temperature set point is selected by using
the “up” or “down” buttons, if unit does not respond push the center “power” button and try again. Test water
to prevent scalding.
iE-18
EL1 L2 L1 L2
Ground Breaker1 Breaker 2
iE-18 - Two 22ov Double Poler 50 amp breakers
iE-24, iE-27
EL1 L2 L1 L2
Ground Breaker1 Breaker 2
iE-24, iE-27- Three 22ov Double Poler 50 amp breakers
L1 L2
Breaker 3
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eccotemp iE series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eccotemp iE series in the language / languages: English as an attachment in your email.

The manual is 3.58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info