Support: Support.Eccotemp.com Shop Online: Eccotemp.com Store Locator: Eccotemp.com/locator
PLEASE NOTE: MINI TANKS ARE FOR INDOOR PERMANENT INSTALLATIONS ONLY. BEFORE POWERING THE WATER HEATER, BE SURE THAT THE SYSTEM IS COMPLETELY FILLED WITH WATER
AND ALL AIR IS REMOVED.THIS MANUAL AND ALL ECCOTEMP CONTENT IS SUBJECT TO CHANGE WITHOUT NOTICE. PLEASE VISIT SUPPORT.ECCOTEMP.COM FOR MORE INFORMATION.
CAUTION! When a supplemental heat source is connected to the Certied
Household Electric Storage Tank Water Heater, provisions must be made to limit the
heat source temperature not to exceed that of the water heater thermostat setting.
CAUTION! If the water heater has been retrotted with supplemental heating
equipment, you must adjust both the thermostat controlling the supplemental heat
source located in the water piping and the thermostat on the water heater behind
the access panel to the same temperature. Failure to adjust both thermostats to the
same temperature can cause loss of proper temperature control.
CAUTION! To reduce the risk of electric shock or re, use only on a utility supply
having a maximum 125/250 volt, three wire system.
CAUTION! To reduce the risk of electrical shock, connect ground to water heater.
For detailed information refer to instructions.
CAUTION! Install temperature and pressure protective equipment required by
local codes, but no less than a combination temperature and pressure relief valve
certied as meeting the requirements for relief valves, ANSI 21.22, by a nationally
recognized testing laboratory that maintains periodic inspection of production of
listed equipment or materials. The valve must be oriented, provided with tubing, or
otherwise installed so that discharge can exit only within 6 inches above, or at any
distance below, the structural oor, and cannot contact any live electrical part.
DANGER! To reduce the risk of electric shock, disconnect from power supply
before replacing temperature-limiting device.
CAUTION! To reduce the risk of excessive pressures and temperatures in this water
heater, install temperature and pressure protective equipment required by local
codes and no less than a combination temperature and pressure relief valve certied
by a nationally recognized testing laboratory that manintains periodic inspection
of production of listed equipment or materials, as meeting the requirements for
Relief Valves and Automatic Gas Shuto Devices for Hot Water Supply Systems,
ANSIZ21.22. This valve must be marked with a maximum set pressure not to exceed
the marked maximum working pressure of the water heater. Install the valve into
an opening provided and marked for this purpose in the water heater, and orient
it or provide tubing so that any discharge from the valve exits only within 6 inches
above, or at any distance below, the structural oor, and does not contact any live
electrical part. The disharge opening must not be blocked or reduced in size under
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Eccotemp ESH 4.0 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Eccotemp ESH 4.0 in the language / languages: English as an attachment in your email.
The manual is 2.85 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
