782663
9
Zoom out
Zoom in
Previous page
1/20
Next page
8Product Support: Eccotemp.com/help-desk Shop Online: Eccotemp.com/products Store Locator: Eccotemp.com/locator 9
Product Support: Eccotemp.com/help-desk Shop Online: Eccotemp.com/products Store Locator: Eccotemp.com/locator
Phone: 866-356-1992 | Email: Support@eccotemp.com Address: 315 - A Industrial RD Summerville, SC 29483 Phone: 866-356-1992 | Email: Support@eccotemp.com Address: 315 - A Industrial RD Summerville, SC 29483
PLUMBING CONNECTIONS
Connect the cold-water inlet pipe to the inlet nipple (marked with a blue ring) and
the hot water outlet pipe to the outlet nipple (marked with a red ring).
IMPORTANT: If Water pipes are copper or bronze, use dielectric connections to
prevent corrosion. Failure to provide dielectric insulation may result in premature
tank or nipple failure and may void your warranty. Ensure that the water heater
is installed in a level position. Install a shut off valve on the cold water side of the
water heater. The valve is for servicing and the valve should be in the open position
when the water heater is in operation. In order to protect the water heater from
heat damage due to soldering, solder a piece of tubing to a threaded UNION tting
before screwing the UNION to the tank.
DO NOT APPLY HEAT DIRECTLY TO INLET OR OUTLET CONNECTIONS.
TEMPERATURE AND PRESSURE RELIEF VALVE:
CAUTION!: Install the Temperature/Pressure Relief Valve supplied with the water
heater!
CAUTION: To reduce the risk of excessive pressures and temperatures in this
water heater, install temperature and pressure protective equipment required
by local codes and no less than a combination temperature and pressure relief
valve certied by a nationally recognized testing laboratory that maintains
periodic inspection of production of listed equipment or materials, as meeting
the requirements for Relief Valves and Automatic Gas Shutoff Devices for Hot
Water Supply Systems, ANSI Z21.22. This valve must be marked with a maximum
set pressure not to exceed the marked maximum working pressure of the water
heater. Install the valve into an opening provided and marked for this purpose in
the water heater, and orient it or provide tubing so that any discharge from the
valve exits only within 6 inches above, or at any distance below, the structural
oor, and does not contact any live electrical part. The discharge opening must
not be blocked or reduced in size under any circumstances.
Install a discharge pipe from the temperature/pressure relief valve terminating
at a sink or drain. DO NOT CAP OR PLUG THE END OF THE DISCHARGE PIPE. THE
DISCHARGE PIPE MUST BE UNOBSTRUCTED AND FULLY SIZED.
A nationally recognized test lab that maintains periodic inspections of the listed
equipment and meets the requirements for relief valves certies the T/P valve and
automatic shut off devices for hot water supply systems ANSI Z21.22.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eccotemp EM 7.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eccotemp EM 7.0 in the language / languages: English as an attachment in your email.

The manual is 3.53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info