611764

Ebode IR Link Pro Mini Manual

5
Zoom out
Zoom in
Previous page
1/44
Next page
22-3-2012 Rev 3 5 IR Link Pro Mini
1. Attach the 3IREDB Emitters onto the IR Sensor Windows of the components in your system that
you wish to control. Refer to Fig. 2.
Tech Tip: By using a flashlight to shine on the display of your Audio/Video device, you can easily
see where to place the emitters.
2a. Plug the yellow mini plugs of the 3IREDB into one of the yellow labelled
"EMITTERS" jacks of the IRHUB4 Connecting Hub.
2b. Plug the IRQC cable into one of the yellow labelled “EMITTERS” jacks of
the IRHUB4, and the other side into the 3.5 mm mono IR input of your AVR.
IRED Mono TS 3.5mm pin configuration: tip is IR Data, sleeve is Ground.
(PLEASE CHECK THE MANUAL OF THE DEVICE FOR MATCHING PIN
CONFIGURATION)
3. Position the IRLPRO Mini IR Receiver in a location outside of the equipment cabinet or closet
that will have a straight line-of-sight view of your Hand Held Remote(s). The Receiver can be fixed
to the surface by using the double side tape pad.
4. Plug the red mini-plug of the IRLPRO Mini IR Receiver into the red labelled "IR RCVR" jack on the
IRHUB4 Connecting Hub.
5. Plug the 12VDC Power Supply into an unswitched 230V~50Hz outlet.
NOTE: It is important that you use an unswitched AC outlet so that the IR system is always active
for system power ON commands.
6. Plug the 2.1mm "C" plug of the Power Supply Adapter into the "+12VDC" jack on the IRHUB4
Connecting Hub.
STATUS
You can send a Power Status signal to the IRLPRO Mini IR Receiver by connecting a power
adapter to this connection (not supplied), which e.g. is switched by the device to be controlled.
When the A/V device or contact is switched on, the Amber Status LED will light up in the IRLPRO
Mini IR Receiver so that you can see that the A/V device is switched on. (see figure 3). The input
voltage range is 5–24VDC & 5–12VAC. Socket 2.1mm, pin configuration: centre/red is ST/+VDC,
sleeve/black is GND.
Fi
g
2
Fi
g
3
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ebode IR Link Pro Mini at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ebode IR Link Pro Mini in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info