611763
20
Zoom out
Zoom in
Previous page
1/44
Next page
7-4-2011 Rev2 20 IR Link Pro Flush
1. Fäst de 3IREDB-sändarna på IR-sensorfönstren på de komponenter i ditt system som du vill styra.
Se Fig 2.
2a. Anslut de gula minikontakterna från 3IREDB till någon av de gula
"EMITTERS"-uttagen på IRHUB4 anslutningsmodul.
2b. Anslut IRQC-kabeln till någon av de gula “EMITTERS”-uttagen på
IRHUB4 och den andra änden i 3,5 mm monoingång på din AVR. IRED
Mono TS 3,5mm stiftskonfiguration: spets är IR-data, mantel är Jord.
(KONTROLLERA I MANUALEN FÖR ENHETEN FÖR PASSANDE
STIFTSKONFIGURATION)
3. Borra ett hål 12 mm bred där du vill placera IR-mottagare. Ta bort mutter, tryck mottagaren
kabel och tråd genom hålet med objektivet in i rummet (och i line-of-sight av fjärrkontrollen).
Skruva loss muttern tills hårt att hålla mottagaren på plats.
4. Anslut den röda minikontakten från IRLPRO Flush IR-mottagaren till det röda "IR RCVR"-uttaget
på IRHUB4 anslutningsmodul.
5. Anslut 12 V-likströmsenheten till ett obrutet 230V~50Hz uttag.
OBS: Det är viktigt att IR-systemet ansluts via ett obrutet uttag så att systemet alltid är aktiverat för
kommando för systemstart, ON.
6. Anslut 2,1 mm "C"-kontakten till strömadaptern till "+12VDC"-uttaget på IRHUB4
anslutningsmodul.
STATUS
Du kan skicka en strömstatussignal till IRLPRO Flush IR-mottagaren genom att ansluta en
strömadapter till denna anslutning (medföljer inte; 5 – 24 VDC & 5 12 VAC) som exempelvis kan
brytas av enheten som styrs. Då A/V-enheten eller kontakten är tillslagen tänds den gula LED-
lampan på IRLPRO Flush IR-mottagaren för att visa att A/V-enheten är tillslagen. (se fig 3).
Ingångsspänning ska vara 5 – 24 VDC & 5 12 VAC. Uttag 2,1 mm pi konfiguration: centrum/röd är
+VDC, mantel/svart är Jord.
Fi
g
2
Fi
g
3
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ebode IR Link Pro Flush at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ebode IR Link Pro Flush in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info