611868
9
Zoom out
Zoom in
Previous page
1/24
Next page
Transmitter - Micro Remote Control Module Ref : EMML
July 2009 page 9 EMML
PROGRAMMIERUNG
Um den Mikro-Sender in der Nähe einer anderen Installation in Betrieb
zu nehmen, muss zum Vermeiden von Störungen ein anderer Code
programmiert werden.
Die zu programmierende Adresse besteht aus einem HAUSCODE (von A bis P)
und einem GERÄTECODE (von 1 bis 16). Werksmäßig ist die Adresse des Sender-/
Empfängerpaars ist auf A1eingestellt. Um einen anderen Code einzustellen, gehen
Sie wie folgt vor.
A. Aufrufen des Programmiermodus.
- Drücken Sie gleichzeitig kurz die Tasten START (1) und STOP (0) des Mikro-
Senders. Die LED leuchtet GELB auf.
Anschließend leuchtet die LED einmal rot (für den HAUSCODE) und dann einmal
GRÜN (für das GERÄT) auf. Der Mikro-Sender ist nun auf A-1-eingestellt.
Sie müssen innerhalb von 6 Sekunden den neuen Code programmieren.
B. Einstellen der HAUSCODES.
- Drücken Sie die Taste (1) so oft, wie für den gewünschten HAUSCODE nötig ist
und lassen Sie die Taste anschließend los.
Beispiel: A = einmal drücken, B = zweimal drücken, C = dreimal drücken ... P =
16 Mal drücken.
- Nachdem der HAUSCODE eingestellt wurde, blinkt die GELBE LED dreimal
auf, um zu bestätigen, dass der Code gespeichert und der Programmiermodus
verlassen wurde.
C. Einstellen des GERÄTECODES.
- Wiederholen Sie nur Schritt A.
- Drücken Sie die Taste (0) so oft, wie für den gewünschten GERÄTECODE nötig
ist und lassen Sie die Taste anschließend los. Beispiel: 1 = einmal drücken, 2 =
zweimal drücken, 3 = dreimal drücken ... 16 = 16 Mal drücken.
- Nachdem der Gerätcode eingestellt wurde, blinkt die gelbe LED dreimal auf.
ÜBERPRÜFUNG
Lassen Sie den Mikro-Sender von den Empfängern erkennen.
Überprüfen Sie die ordnungsgemäße Ein-/Ausschaltfunktion.
Sie müssen etwa eine Sekunde zwischen jedem Ein-/Ausschaltbefehl warten.
Bei einem Batteriewechsel bleibt der eingestellte Code im Mikro-Sender
erhalten.
Troubleshooting - Bei Problemen: Prüfen Sie die FAQs und die Technische
Unterstützung auf www.ebodeelectronics.eu.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ebode EMML at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ebode EMML in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish, Norwegian as an attachment in your email.

The manual is 0,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info