Manual Eberspacher Timer Modulator 701 serie (page 2 of 4) (English)

701137

Zoom out

Zoom in

1/4

Instant Heat ON/OFF key

Adjustment Up key

Disengaged pre-set symbol

Ventilation symbol

Temperature ramp.

Current Time, Preset Time,

Heating Time, Run Time

and Diagnostics.

Day selected indicator boxes.

Clock symbol.

Heater operation symbol.

10.

Preset Programme

symbols.

11.

Adjustment Down key.

12.

Programme key.

13.

Set/Programme key.

Low Heat

High Heat

701 Series Timer / Modulator With Diagnostic Readout Instructions

Introduction

Your Timer/Modulator offers manual

and programmable control along with

temperature adjustment of your heater.

When the heater is switched on by the

Timer/Modulator in a programmed

mode it will run for 1 hour or for the

duration time that you have selected e.g

Heater on at 0700, duration time of 1 hour,

which means heater will be switched off

automatically at 0800.

lock Settings:-

Press and hold

key until the

symbol

begins to flash. Use the

and

keys to

set correct time. Press and release the

key and the day box will begin to flash.

Use the

and

keys to set the correct

day. Press and release the

key again to

reset the clock to the start of the minute

displayed. This may be used to coincide

with a known time signal.

Please Note:

These adjustments are not possible

when the heater is in operation. To set the

heater’s programmable switch on timer, see

“Setting Program Times”.

witching on the Heater

(Manually)

Press the

key and the

symbol will

appear on the display. The heater will

commence its startup cycle. The display

will change to show a default of one hour

heating countdown time. This can be

extended

in increments of 10 minutes,

30 minutes, 1 hour, 1 hour 30 minutes, 2

hours

up to eight hours or to continuous

running operation (shown as C-: -- on

display) by repeatedly pressing the

key

while the heater is in operation. Current

time will be displayed every 5 seconds.

Switching off the Heater

(Manually)

The heater may be switched off at any time

by pressing the

key. The cooling down

cycle will then be initiated.

Adjusting the Temperature

Pressing the

and

keys will alter the

20 segment temperature ramp shown on

the display. This level may be adjusted

at any time and will remain in the

timer memory when the heater is not in

operation.

Diagnostic Readout

With the heater switched on, press and

hold

key until the display shows

“dAtA”. Release key and display then

shows “AF--” and alternatively displays

the current fault code. Each press of

the

key will scroll through the last 5

previously stored fault codes.

Typical fault codes -

10 = Over voltage - Check battery charging system.

11 = Under voltage - Check battery voltage.

12 = Overheating - Check air ducts for obstruction.

52 = Safety time exceeded - Check fuel supply.

For other codes consult your local dealer.

Although all the programs are set to "off", the heater still comes on and the only way i can get it to stop is to reduce the temperature.
I have the "c" symbol permanently in the time display so does this mean the heater is operating continuously? How do I turn continuous off? Submitted on 17-10-2020 at 18:23
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Eberspacher Timer Modulator 701 serie in the language / languages: English as an attachment in your email.

The manual is 0,36 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Eberspacher Timer Modulator 701 serie Manual

Product: