701128

Eberspacher EasyStart Pro Manual

17
Zoom out
Zoom in
Previous page
1/28
Next page
4.5.2 Programming the timer
Display ON, the Start display appears.
Select in the menu bar
with the operating
button.
Picture 1: Display if no timer is activated.
Picture 2: Display if a timer is activated, here T2.
Confirm timer selection by pressing the
operating button.
Æ The first timer position T1 appears. Turn the
operating button to select the alternative
timer positions T2 or T3.
30min
Picture 3: T1 with factory settings
The factory settings are:
– Heating mode
– Weekday range Mon – Fri
– Starting time: 7:00 h
– Operating time: 30 minutes
Call up timer T1 by pressing the operating
button. You are now in configuration mode.
The following settings are possible:
– Timer T1 ON / OFF by turning and pressing
the operating button.
– After selecting
in the menu bar, next
select the day of the week / weekday range
by turning the operating button. Each day
of the week is selected individually and
confirmed by pressing. Pressing a second
time deselects the day of the week again. At
the end of the selection, turn the operating
button to [OK] and press to confirm.
Mo
– Step 2: Setting the starting time. Turning
and pressing confirms first the hour, then
the minutes:
– Step 3: Selection of heating or ventilation
mode:
Note
If an air heater is operated with EasyStart Pro,
the desired temperature in heating mode can
also be set before setting the operating time:
14°C – 36°C in 1°C steps,
57°F – 97°F in 1°F steps.
Operating Instructions | EasyStart Pro
22.1000.35.2204.0A EN | 05.2018 17
… 17 …


Need help? Post your question in this forum.

Forumrules
1

Forum

eberspacher-easystart-pro

Reset search

  • rotary knob jammed, how to soldering some stick or wichone on the board pin to change left or right button...? Submitted on 9-1-2022 at 12:58

    Reply Report abuse

  • Is there a 12v switch + on 4 pin connector at easy pro display controller,thanks Submitted on 27-4-2021 at 06:34

    Reply Report abuse

  • Hi can a easy pro timer be turned through deep sea controller , I am looking for a 12v switch + wire that I can use ,send signal to remotely using a relay, the 4 wire on 4pin connector is any one of those a 12+ ,thanks Submitted on 27-4-2021 at 06:28

    Reply Report abuse

  • Bonjour je voudrai la notice en francais du reglage easystart pro merci Submitted on 23-9-2020 at 18:21

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eberspacher EasyStart Pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eberspacher EasyStart Pro in the language / languages: English as an attachment in your email.

The manual is 0,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Eberspacher EasyStart Pro

Eberspacher EasyStart Pro Quick start guide - English, German - 16 pages

Eberspacher EasyStart Pro User Manual - German - 28 pages

Eberspacher EasyStart Pro User Manual - Dutch - 28 pages

Eberspacher EasyStart Pro Quick start guide - Danish, French, Italian, Spanish, Finnish - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info