701117
13
Zoom out
Zoom in
Previous page
1/29
Next page
13
D
S
GB
F
!
Heating air duct (example)
Conducting the combustion air
The combustion air must be drawn in from the out-
side (not from the passenger compartment or boot).
The combustion air intake must be arranged in such
a manner that it cannot draw in any exhaust gas. Do
not position the suction opening of the combustion
air hose in the opposite direction of the air-stream.
Position the combustion air hose in such a manner
that it cannot become clogged with dirt or snow, and
any water that may have entered the hose can freely
drain out again.
At the inlet of the combustion air hose, the terminal
sleeve with web provided for must be mounted
(statutory regulation).
Please note!
Small arrows indicating the flow direction (see
drawing) have been cast into the connecting pieces
so that they can be correctly assigned to
combustion air and exhaust gas (see below).
Danger of burns or injury!
The hoses of the hot air duct and their hot air
exhaust must always be laid and mounted in such
a manner that no thermal danger arises from them
for man, beast or heat-sensitive material due to
radiation / contact or due to hot air being directly
blown onto them.
The exhaust hood must be pushed on at the hot air
exhaust side.
If no air hoses have been mounted, a protective grille
must be pushed on at the hot air suction side and
exhaust side to avoid injuries due to the hot air fan
and/or burns due to the heat exchanger.
High temperatures occur on the hot air duct during
and also immediately after heating operation. Avoid
thus any work in the area of the hot air duct during
heating operation. In such a case, switch off the
AIRTRONIC
beforehand and wait until all parts have
completely cooled down.
If necessary, wear protective gloves.
The heating air intakes have to be arranged in such a
manner that, under normal operating conditions, they
cannot draw in exhaust fumes from the vehicles engine
and from the
AIRTRONIC
, and that the heating air
cannot be polluted by dust, salt fog, etc.
In recirculation mode, the recirculated air inlet has to
be positioned in such a manner that the outflowing hot
air cannot be directly drawn in again.
When checking the functions, the mean exhaust
temperature after approx. 10 minutes of operation
measured approx. 30 cm from the air outlet should
not exceed 110 °C at an intake temperature of
approx. 20 °C.
Protective grille
Outflow hood
Hose clamp
Flexible tube
Air outlet, rotatable
Connecting piece
Protective grille
6
7 3 4
1
3 4
2
3 5
Please note!
When connecting up parts conducting air, please
observe the device guide number in the technical
specifications (see page 6)!
In the case of a possible malfunction due
to overheating, heating air temperatures of up
to max. 180 °C and surface temperatures of up
to max. 150 °C may occur locally immediately prior
to malfunction cut-off.
For this reason, only heat-resistant hot air hoses
approved by us may be used for the hot air duct!
ATTENTION!
Visit www.butlertechnik.com for more technical information and downloads.
www.butlertechnik.com
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eberspacher AIRTRONIC D4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eberspacher AIRTRONIC D4 in the language / languages: English as an attachment in your email.

The manual is 2,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Eberspacher AIRTRONIC D4

Eberspacher AIRTRONIC D4 Usermanual and installation guide - Dutch - 37 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info