703773

Easymaxx HDY01A0 - Z08630 Manual

4
Zoom out
Zoom in
Previous page
1/8
Next page
EN Instructions
Customer Service / Importer:
DS Direct GmbH, Am Heisterbusch 1, 19258 Gallin, Germany • ✆ +49 38851 314650 *)
*) Calls to German landlines are subject to your provider’s charges.
All rights reserved.
Device Overview
Check the items supplied for completeness and possible transport
damage. If you should fi nd any transport damage, do not (!) use the
device, but contact the customer service department immediately.
1 LED projector
2 Lens unit
3 Template holder
4 Motif template
5 Projector holder
6 Base
7 Ground spike
8 Mains adapter
9 Locking screw
10 Template mount
(in the projector housing)
3
4
5
1
8
7
6
10
2
9
Rear View
11 Button : Rotation On / Off
12 Speed / On / Off switch:
60 seconds per rotation
Off
200 seconds per rotation
13 Cap nut
Setting Up and Using the Projector
PLEASE NOTE!
■ Do not leave the device switched on for longer than 24 hours. It
is not suitable for continuous operation.
1. Screw the projector holder (5) to the base (6) to set it up or to
the ground spike (7) to anchor it in the ground.
2. Screw the LED projector (1) securely to the projector holder
using the locking screw (9) and the nut. Note the alignment of
the LED projector.
3. Set up the LED projector no more than 10 m away from the
object which is to be illuminated. When using the ground spike,
anchor it fi rmly in the ground.
4. Adjust the alignment of the LED projector again if necessary.
5. Insert the motif template (4) into
the template holder (3).
Important:
Make sure that the
two pins on the motif template sit
in the recesses which are provid-
ed for them in the template holder.
6. Insert the template holder with the
inserted template into the template
mount in the projector housing (10).
Important: Make sure the template
holder is in the correct position for
the insertion of the template (see
picture).
7. Insert the small plug of the mains adapter (
8
) into the socket on
the back of the LED projector and screw the cap nut (
13
) onto the
thread of the LED projector.
8. Connect the mains adapter to a properly installed plug socket.
9. To switch on the device, slide the Speed / On / Off switch (12)
to the position or .
With switch (11) the rotation of the motifs can be
activated or deactivated.
10. To switch off the device, move the Speed / On / Off switch to
the position.
Cleaning and Storage
PLEASE NOTE!
■ Do not use any corrosive or abrasive cleaning agents to clean
the device. These could damage the surface.
• Make sure that the lens unit (2) is always clean. You should
therefore clean it with a damp cloth from time to time.
• Store the device in a dry place that is protected from sunlight
and is not accessible to children and animals when you are not
using it.
Technical Data
Article number: 08630
ID instructions: Z 08630 M HSV V3 0719
Projector
Model number: HDY01A0
Voltage: 5 V DC
Power: 7.5 W (max.)
Protection class: III
Type of protection: IP64
Brightness: 25 lumen
Risk group in
accordance with
DIN EN 62471:2008: 2
Mains adapter
Model number: GQ12-050150-AGO
Voltage:
– IN: 100 – 240 V ~ 50 / 60 Hz, 0.4 A
– OUT: 5 V DC, 1.5 A
Protection class: II
Type of protection: IP44
Disposal
Dispose of the packaging material in an environmentally
friendly manner and take it to a recycling centre.
This device is governed by the European Directive
2012/19/EU on waste electrical and electronic equipment
(WEEE). Do not dispose of this device as normal domestic
waste, but rather in an environmentally friendly manner via
an offi cially approved waste disposal company.
11
12
13
Article number: 08630
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Easymaxx HDY01A0 - Z08630 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Easymaxx HDY01A0 - Z08630 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info