515345
7
Zoom out
Zoom in
Previous page
1/32
Next page
7
Select user language / record individual message Details according to section 6.3
12. Slide function switch to PROG
13. Enter *. *. #.
Current individual message will be announced followed by “to modify press * , to stop press #
14. Select language for user announcements: (facultative)
Press key 1 to 4 to select user languages: 1 for German, 2 for French, 3 for English GB, 4 for Italian
15. Press * and start speaking
16. Press # to finish recording, max. duration is 12 seconds
New individual message will be announced. You can repeat steps 14 to 16 until text is fine!
17. Slide function switch to OFF
Program PIN-code Details according to section 6.4
18. Slide function switch to PROG
19. Press key #.
You can prevent the alarm unit from unintended re-programming by pressing * ..
20. Enter PIN-code (4 to 7 digits)
21. Press key #.
22. Re-enter PIN-code for confirmation
23. Press key #.
New PIN-code will be announced
24. Slide function switch to OFF
Alarm unit is now ready for operation Details according to section 7
25. Slide selection switch to the requested position (I/II/III)
4.1.4 Activation of motion sensor
Provided the motion detector is plugged in, EasyAlar detects the motion detector during the switching on procedure.
Important notes:
By disconnecting the motion detector during the operation mode, an alarm is
triggered followed by the announcement: ”alarm due to sensor 1, sensor failure!”
By connecting the motion detector after the start up procedure of the alarm unit,
an alarm is triggered followed by the announcement: “alarm due to sensor 1,
sensor 1 activated!
4.1.5 Deactivation of motion sensor
If the motion detector is not plugged in, EasyAlarm® automatically deactivates the
supervision of the motion detector.
4.1.6 Adjustment
Safety note:
Before you open cover please check, that the telephone cord is DISONNECTED.
Otherwise you can get in contact with the telecommunication voltage!
Remove the front cover by twisting a flat screwdriver in the slot between the cover and
the base at the bottom of the motion detector
4.1.6.1 Pulse count
You can set PULSE jumper at position 1,2 or 3 corresponding to the desired pulse count
before an alarm will be triggered. Default = 2.
4.1.6.2 WALK-test
To disable LED indication, remove the LED jumper and place it on one pin only. To
activate LED indication, place LED jumper over both pins.
4.1.6.2.1 Mounting height
If motion detector is not mounted at 2.5m you can adjust like this:
1. Loosen the PC-Board holding screw. Slide the PC-Board so that the plastic pointer
on the right side is positioned at the appropriate scale position.
For higher than 2.5m => Slide PC-Board up
For lower than 2.5m => Slide PC-Board down
2. Tighten the PC-Board holding screw
3. Mount front cover
4. Walk through the entire protected area and observe the LED to ensure full coverage
Mounting screw
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for EasyAlarm CONTROL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of EasyAlarm CONTROL in the language / languages: English as an attachment in your email.

The manual is 0,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of EasyAlarm CONTROL

EasyAlarm CONTROL User Manual - German - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info