515344
22
Zoom out
Zoom in
Previous page
1/32
Next page
22
9. TROUBLE SHOOTING / ERROR HANDLING
Most problems can be checked and solved with help of the following chart. If the problem remains after consulting this
chart in details, please get in touch with your local dealer or contact the info line of your country, see section 12.3.
9.1 Telephone connection / Telephone communication
Symptoms Cause and /or remedy
LED is not lit after switching ON Replace battery
Announcement „programming deactivated:
PIN“ by an attempt of reprogramming
Programming function is locked => to be unlocked according to section
6.4.2
Announcement „Beep Beep Beep“
Announcement „battery error”
Mains loss and low battery at the same time!
Battery is low => replace battery
Announcement „power failure” Power failure, transformer not connected
Announcement „line check error “
No dial tones are audible during test call =>
no tones are audible during the dialling
procedure
No dial tone has been detected:
Unit is not connected with the telephone network
Telephone network failure
Another telephone working on the same phone line is occupying the
line already
Plug in telephone cord
Check the telephone cord
Start test-call with different telephone
Test call does not call first calling number in
the calling number sequence:
Announcement „calling number error“
Calling number (n=2..9) is not programmed => Calling number 1 was
dialled instead
Test call does not establish phone
connection: Announcement „calling number
n“ => dial tone audible
Calling number is wrong
Called party is not answering the phone
Remote access using dialling-in not possible
=> EasyAlarm® is not responding to the
call
The dialling function is programmed for the two step modus (
section 10.7.2)
Remote access using dialling-in not possible
=> disconnection after entering of PIN-code
Wrong PIN-code entered => call again
EasyAlarm® does not react on tone-
dialling commands
Current telephone does not support tone-dialling commands or has not been
configured => for example pulse dialling
9.2 Motion detector used as an alarm-sensor (sensor-1/2)
Symptom Cause and / or remedy
LED is on during WALK TEST, but no
alarm is triggered
Inactive waiting period by switching on the unit or between two alarms
is not expired
Supervision has been temporarily deactivated (deactivation)
Supervision is deactivated at current position of the selection switch
(I/II/III) ( section 5.1)
Motion detection is programmed to verify presence ( section
5.1.2.1), an alarm is only triggered if no motion is detected over a
programmed time.
Only sensors with contact type set to other value than inactive (00) will
be announced => see configuration in section 5.
Test mode => check section 4.2.3
WALK TEST has been set, but LED is not
on
Power supply of the motion detector is missing (=> check cable,
connector and power supply)
Power supply not on since two minutes (stabilize time of PIR-motion
detector)
There is no motion and the WALK TEST
LED is not on, but alarming with periodical
announcement „alarm sensor n“ is spoken
Power supply of the motion detector is missing (check cable, connector
and power supply) => further announcement „power failure “
The motion detector has been connected (additional announcement
„sensor 1 activated“ or disconnected (additional announcement “sensor
failure”) after power on => factory setting automatically recognizes a
connected Plug&Protect-motion detector
„Alarm due to sensor n“ is announced, but
the motion detector has been temporarily
deactivated
The power supply of the unit has been cut off for a short period
The function switch has been switched to PROG or OFF after
temporarily deactivation.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for EasyAlarm BASIC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of EasyAlarm BASIC in the language / languages: English as an attachment in your email.

The manual is 0,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of EasyAlarm BASIC

EasyAlarm BASIC User Manual - German - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info