Manual Eagle FishElite 500C (page 37 of 204) (English)

522010

Zoom out

Zoom in

1/204

Thoroughly stir the two compounds together until the mixture has a

uniform color and consistency. Do not mix too fast or bubbles will form

in the epoxy. After mixing, you have 20 minutes to complete the in-

stallation before the epoxy becomes unworkable.

Spread a thin layer of epoxy (about 1/16" or 1.5 mm thick) on the face of

the transducer as shown in the previous figure. Make sure there are no

air pockets in the epoxy layer! Then, apply the remaining epoxy to the

sanded area on the hull.

3. Press the transducer into the epoxy, twisting and turning it to force

any air bubbles out from under the transducer face. Stop pressing when

you bottom out on the hull. When you're finished, the face of the trans-

ducer should be parallel with the hull, with a minimum amount of ep-

oxy between the hull and transducer.

4. Apply a weight, such as a brick, to hold the transducer in place while

the epoxy cures. Be careful not to bump the transducer while the epoxy

is wet. Leave the weight in place for a minimum of three hours. Allow

the epoxy to cure for 24 hours before moving the boat.

5. After the epoxy has cured, route the cable to the sonar unit and it's

ready to use.

Speed/Temperature Sensors

This unit can accept as many as two temperature sensors, which can be

used to monitor the temperature of surface water, a live well or some

other location. These units can also accept an optional speed sensor for

showing speed and distance traveled. However, you can only use one ac-

cessory at a time. If you would like to use a speed sensor and a second

temperature sensor at the same time, you will need a combination device.

NOTE:

This unit is packed with a transducer containing a built-in temp sensor.

The SeaCharter package also includes a speed sensor. If you have a

FishElite 500C and want a speed sensor or additional temp sensor, see

the Accessory Ordering Information in the back of this manual.

If a second temp sensor is used, it must be the model TS-2U. This

model has a fixed electronic "address" which designates it as the second

of two temp sensors. Dual temperatures are only displayed on the Full

Chart page. The Large Digital page will only display the primary tem-

perature sensor. See the following wiring diagram for temperature and

speed sensor combinations.

www.Busse-Yachtshop.de email: info@busse-yachtshop.de

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Eagle FishElite 500C in the language / languages: English as an attachment in your email.

The manual is 3,93 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Eagle FishElite 500C Manual

Product: