702458
22
Zoom out
Zoom in
Previous page
1/24
Next page
Ensure the
machine
is plugged in and
switched on. Check the fuse and also
that the circuit breaker has not tripped.
(See
section 02)
for the programme
options wash table.
Wait for the machine to finish the cycle
before opening the door. To cancel the
wash hold down the
‘Cancel’
button.
Press ‘Start’ to resume the wash.
Hold down the
‘Minimum iron
button until
‘Child lock off’ is shown on LCD display.
Follow the ‘Emergency door release’
instructions in (section 03).
Turn off the water supply to the machine
and ensure that the coin trap cover is
correctly fitted and that the plug is closed,
(see section 02).
Adjust the feet until the machine is level,
(see section 03).
Check the drainage hose is draining
into a suitable place (drain, sink or
standpipe), (see section 02).
Ensure the hoses are fitted correctly,
(see section 02).
Close the soap tray.
Remove soap tray and clean((
Adjust feet until the machine is level,
(see section 02).
Return the Rollerjack
TM
handle carefully
to its position under the machine,
(see section 01).
Remove top, rear and front packaging,
(see section 01).
Call Dyson helpline.
Check orientation of hot and cold pipes.
4
4
5
5
5
5
10
10
9
LCD display is blank
Certain spin speeds, temperatures or
soil types cannot be selected
Cannot open outer door
Machine leaks water
Machine shakes during the cycle
Burning smell
Clothes warm at end of cycle
There is no power to the
machine.
There are limits set on these options for
each programme to prevent unsuitable
options being selected.
Machine has not finished the cycle.
Machine has paused and the water level
is too high or the water is too hot.
Child lock is active.
Power cut or any other cause not listed
above.
Coin trap cover is not in place, or the
plug is not closed.
Machine is not level.
Drainage hose is not connected correctly.
Inlet hoses are not positioned or
correctly fitted.
Soap tray is open.
Soap tray is blocked with detergent
2 adjustable front feet are not level.
Rollerjack
TM
handle has not been replaced
under the machine.
Transit packaging not removed.
Transit packaging is removed
Hot and cold pipes reversed.
11 02Troubleshooting
Symptom
Some solutions may require you to disconnect the electricity and water supply.
Possible causes
Solutions
Remove soap tray and clean (see section 01).
10
8887_CRO2_OPS_INNERS.qxd 5/11/03 3:28 pm Page 20
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dyson CR02 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dyson CR02 in the language / languages: English as an attachment in your email.

The manual is 1,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info