585220
7
Zoom out
Zoom in
Previous page
1/21
Next page
6
Inserting the Optional Battery Pack
The printer can operate using an optional rechargeable,
Lithium-ion battery pack (DYMO Li-ion Battery 7.4V
1400mAh).
Make sure the power adapter is disconnected
before handling the Lithium-ion battery pack.
To insert the battery pack
1
Press the thumb latch on the back of the printer to
remove the battery compartment cover. See Figure 4.
Figure 4
2 Insert the battery pack into the battery compartment
following the polarity markings. See Figure 4.
3 Replace the battery compartment cover.
Make sure to read the Lithium-ion Safety
Precautions found on page 19.
Removing the Optional Battery Pack
Remove the battery pack if the printer will not be used for
a long period of time.
Make sure the power adapter is disconnected
before handling the Lithium-ion battery pack.
To remove the battery pack
1 Unplug the power adapter.
2 Press the thumb latch on the back of the printer to
remove the battery compartment cover.
3 Remove the battery from the battery compartment.
Make sure to read the Lithium-ion Safety
Precautions found on page 19.
Recharging the Battery Pack
The battery pack automatically recharges while the printer
is connected to a power source through the power
adapter. Charging the battery pack for the first time will
take approximately eight hours; recharging the battery
pack will take approximately two hours.
Inserting and Removing the Label Cartridge
Your printer comes with a starter label cartridge. Visit
www.dymo.com for information about purchasing
additional label cartridges.
To insert the label cartridge
1 Gently lift the label cartridge door on the back of
the printer.
2 Make sure the label and ribbon are taut across the
mouth of the cartridge and that the label passes
between the label guides.
If necessary, turn the ribbon rewind spool clockwise
to tighten the ribbon.
3 Insert the cartridge with the label and ribbon
positioned between the label guides. See Figure 5.
Figure 5
4 Press firmly on the cartridge until the cartridge snaps
into place.
To avoid label jams, make sure both sides of the label
cartridge snap into place.
5 Close the label cartridge door.
To remove the label cartridge
1 Gently lift the label cartridge door on the back of the
printer.
2 Gently remove the label cartridge.
3 Insert a new label cartridge as described above.
4 Select the width of the new label cartridge when
prompted.
Setting the Label Width
Each time you insert a label cartridge into the printer, you
are prompted to set the label width so the printer knows
what size label you are currently using. Some of the
features you use to design labels depend on the width of
the label. You can change the label width setting at any
time from the Settings menu.
To set the label width
1 Press + .
2 Select Print options and press .
3 Select Label width and press .
4 Select the width of the label currently inserted in the
printer and press .
Press thumb
latch to open
Lift
Label guides
Ribbon
rewind spool
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dymo Rhino 4200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dymo Rhino 4200 in the language / languages: English as an attachment in your email.

The manual is 14,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dymo Rhino 4200

Dymo Rhino 4200 User Manual - German - 22 pages

Dymo Rhino 4200 User Manual - Dutch - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info