787502
5
Zoom out
Zoom in
Previous page
1/33
Next page
ASSEMBLY INSTRUCTIONS
WARNING
Assemble the device in the identified order. Only use the provided tools
(73 + 74).
Carry and move the device with at least two persons.
Place the device on a firm, dry and level surface and protect it from
moisture and water.
Place the device on a protective base to prevent damage to the
floor surface.
Allow at least 100 cm of clearance around the device.
Refer to the illustrations to know how to correctly assemble the device.
STEP 1:
Fix the front stabilizer (2) and rear stabilizer (3) into the main frame (1) using
the carriage bolt (46), arc washer (42) and the cap nut (47).
1
STEP 2:
a. Fix the handrail arm (4L/R) into the main frame (1) using the long axle
(12), bolt (57), spring washer (52), D washer (56) and washer (67).
NOTE: do not tighten firmly.
b. Fix the right pedal tube (6R) to the crank (27) using the bolt (62R), spring
washer (51) and nylon nut (48R). You can now fully tighten the bolt (57),
bolt (62R) and nylon nut (48R). Fix the left pedal tube (6L) using the
same means of assembly. Finally, put on the cap (68). Finally, put on the
caps (68/96).
NOTE: The right and left bolt (62L/R) are marked with “R” & “L” respectively.
The bolt (62R) should be threaded in a clockwise direction. The bolt (62L)
should be threaded in a counter clockwise direction. You can adjust the
crank, so it becomes easier to tighten the bolts.
2
STEP 3:
Attach the pedal (11L/R) to the pedal tube (6L/R) using the bolt (44) and
nylon nut (45).
3
STEP 4:
Attach the handrail (7L) to the handrail arm (4L) using the knob (17). Attach
the handrail (7R) using the same means of assembly. Finally, put on the
cap (71).
STEP 5:
Connect the sensor wire (26) to the upper sensor wire (37) and attach the
small tube (28) to the main frame (1) using knob (17). Then fix the vertical
tube (72) into the small tube (28) using the bolt (43) and big washer (41).
Finally, put on the cap (71).
4 5
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dutch Originals K8.2D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dutch Originals K8.2D in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4.79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info