612078
61
Zoom out
Zoom in
Previous page
1/64
Next page
Troubleshooting
Operating Instructions 841 - 00.0 - 09/2014
59
4307 Memo dongle Wrong class Wrong class dongle
attached
Attach correct dongle
Format dongle
5101 Contour data
management
EEPROM not
initialized
Controller
Controller does not contain
a machine program
Check the controller
Install a machine program
5104 Contour data
management
EEPROM
checksum fault
Controller Machine performing a reset
automatically.
Inform DA Service
5301 Contour data
management
No contour data Cutting length smaller than
length of cutter
Change parameters
5302 Contour data
management
Data memory full Too many stitches in con-
tour
Reduce number of stitches
Inform DA Service
5303 Contour data
management
Data memory
overflow
Too many stitches in con-
tour
Reduce number of stitches
Inform DA Service
5305 Contour data
management
Storage not
permitted
Too many stitches in con-
tour
Reduce number of stitches
Inform DA Service
5306 Contour data
management
Impermissible
data call
Perform a buttonhole contour
reset
Inform DA Service
5315 Contour data
management
General fault Perform a buttonhole contour
reset
Inform DA Service
6151-6952 I²C/CPU/Mem
Manager
Fault Switch the machine off and
on again
Inform DA Service
7251-7659 ASC/SSC/
RS485
Fault Switch the machine off and
on again
Inform DA Service
8151-8351 IDMA/Xilink/Test
pins
•Fault
(8151-8159: only entry in
event recorder – no other
impairment)
Switch the machine off and
on again
Inform DA Service
9700 Machine/
process
Basket not lifted
up
Basket monitoring sensor
not active
Check distance to sensor
Check sensor
9702 Machine/
process
Infeed table not in
transfer position
Infeed table sensor not
active
Check ease of movement/
alignment
9703 Machine/
process
Maximum position
exceeded
Distance between button-
holes too great
Correct program
Number Location Description Possible cause Remedial action
61


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Durkopp Adler 841 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Durkopp Adler 841 in the language / languages: English as an attachment in your email.

The manual is 3,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Durkopp Adler 841

Durkopp Adler 841 User Manual - German - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info