612086
16
Zoom out
Zoom in
Previous page
1/27
Next page
ATTENTION !
During the use of the setting program do not turn on the handwheel or
the hand crank!
If necessary, lower the sewing arch by pressing the
F3 key
.
With the setting aid still turned on the knife block can now be
moved downward with the
F4 key
.
By pressing the
F4
key
again the knife block can be run up again.
If the sewing arch is not lowered the knife block can not be run
downward with the
F4
key
. First the sewing arch must then be lowered
with the
F3
key
. Also the function of the
F3 key
(lift sewing arch) is
blocked with the knife lowered.
Setting the knife to cut
With the knife block lowered and the knife depth stop screwed
completely in, the knife should lay onto the plastic cutting block.
Setting:
Lower the knife block.
Slightly loosen nut 1.
Press the knife onto the cutting block.
Tighten nut 1.
Conduct a sewing trial and check the cut, if necessary correct the
cutting depth with the knife stop.
The incision of the knife should lie about 2 fabric threads in front of the
last sewn back tack.
Setting:
Loosen screw 3 and set the clearance accordingly.
Observe:
With the knife block lowered there
must
be a safety clearance of
0.5 mm
between the front edge of the knife and the slot in the needle
plate insert.
Tighten screw 3.
Ending the setting aid
Press the "
F1
" key.
The setting program is ended.
4.10 Replacing the Plastic Cutting Plate (only with Cutting Block)
Loosen screws 4.
Pry out cutting plate 5 with a screwdriver and remove it.
Insert a new cutting plate, press on the holder and tighten the
screws 4.
Conduct the setting as per the Chapter " Replacing and Setting the
Knife (Cutting Block)".
18
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Durkopp Adler 841-27 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Durkopp Adler 841-27 in the language / languages: English as an attachment in your email.

The manual is 2,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Durkopp Adler 841-27

Durkopp Adler 841-27 User Manual - German - 27 pages

Durkopp Adler 841-27 User Manual - French - 27 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info