612088
57
Zoom out
Zoom in
Previous page
1/80
Next page
Connect the 9-pole SuB-D plug of the Hall-effect sensor to the
bushing “B18" (IPG / HSM / LSM) of the Efka control drive DA321G.
Set the correct machine class with parameter F-290 according to
the corresponding parameter sheet 9800 331104 PBXX.
In order to position the machine correctly and to optimize all
functions the following parameters must still be set:
Parameter F-111: set to 3,000 rpm or less.
Parameter F-270: set to 6 (selection according to the position sensor)
Parameter F-272: can be calculated according to the formula below:
Motor pulley diameter (teeth)
x 1000
Machine pulley diameter (teeth)
Inserted needle: up to a thickness of 160.
Due to the gear reduction of 1.55:1 the maximum possible speed
is 3,000 rpm.
Due to the new transmission ratio of 1,55:1 a higher torque and a
higher penetration force of the needle of about 30% above a
transmission rate of 1:1 is achieved.
In order to achieve an even higher penetration force, the parameter
F-225 can be set from value “0" to value ”1".
It may happen, that the motor produces a snarling noise.
If this is the case, the toothed belt between motor and machine must
be tightened.
21
B 7 7 6
V 8 . .
B 1 8
L S M . . .
B 2
M
B 8 0
E B . . .
B 4 1
M
A
Connect the 9-pole SuB-D plug of the Hall-effect sensor to the
bushing “B18" (IPG / HSM / LSM) of the Efka control drive DA321G.
Set the correct machine class with parameter F-290 according to
the corresponding parameter sheet 9800 331104 PBXX.
In order to position the machine correctly and to optimize all
functions the following parameters must still be set:
Parameter F-111: set to 3,000 rpm or less.
Parameter F-270: set to 6 (selection according to the position sensor)
Parameter F-272: can be calculated according to the formula below:
Motor pulley diameter (teeth)
x 1000
Machine pulley diameter (teeth)
Inserted needle: up to a thickness of 160.
Due to the gear reduction of 1.55:1 the maximum possible speed
is 3,000 rpm.
Due to the new transmission ratio of 1,55:1 a higher torque and a
higher penetration force of the needle of about 30% above a
transmission rate of 1:1 is achieved.
In order to achieve an even higher penetration force, the parameter
F-225 can be set from value “0" to value ”1".
It may happen, that the motor produces a snarling noise.
If this is the case, the toothed belt between motor and machine must
be tightened.
21
B 7 7 6
V 8 . .
B 1 8
L S M . . .
B 2
M
B 8 0
E B . . .
B 4 1
M
A
Connect the 9-pole SuB-D plug of the Hall-effect sensor to the
bushing “B18" (IPG / HSM / LSM) of the Efka control drive DA321G.
Set the correct machine class with parameter F-290 according to
the corresponding parameter sheet 9800 331104 PBXX.
In order to position the machine correctly and to optimize all
functions the following parameters must still be set:
Parameter F-111: set to 3,000 rpm or less.
Parameter F-270: set to 6 (selection according to the position sensor)
Parameter F-272: can be calculated according to the formula below:
Motor pulley diameter (teeth)
x 1000
Machine pulley diameter (teeth)
Inserted needle: up to a thickness of 160.
Due to the gear reduction of 1.55:1 the maximum possible speed
is 3,000 rpm.
Due to the new transmission ratio of 1,55:1 a higher torque and a
higher penetration force of the needle of about 30% above a
transmission rate of 1:1 is achieved.
In order to achieve an even higher penetration force, the parameter
F-225 can be set from value “0" to value ”1".
It may happen, that the motor produces a snarling noise.
If this is the case, the toothed belt between motor and machine must
be tightened.
21
B 7 7 6
V 8 . .
B 1 8
L S M . . .
B 2
M
B 8 0
E B . . .
B 4 1
M
A
Connect the 9-pole SuB-D plug of the Hall-effect sensor to the
bushing “B18" (IPG / HSM / LSM) of the Efka control drive DA321G.
Set the correct machine class with parameter F-290 according to
the corresponding parameter sheet 9800 331104 PBXX.
In order to position the machine correctly and to optimize all
functions the following parameters must still be set:
Parameter F-111: set to 3,000 rpm or less.
Parameter F-270: set to 6 (selection according to the position sensor)
Parameter F-272: can be calculated according to the formula below:
Motor pulley diameter (teeth)
x 1000
Machine pulley diameter (teeth)
Inserted needle: up to a thickness of 160.
Due to the gear reduction of 1.55:1 the maximum possible speed
is 3,000 rpm.
Due to the new transmission ratio of 1,55:1 a higher torque and a
higher penetration force of the needle of about 30% above a
transmission rate of 1:1 is achieved.
In order to achieve an even higher penetration force, the parameter
F-225 can be set from value “0" to value ”1".
It may happen, that the motor produces a snarling noise.
If this is the case, the toothed belt between motor and machine must
be tightened.
21
B 7 7 6
V 8 . .
B 1 8
L S M . . .
B 2
M
B 8 0
E B . . .
B 4 1
M
A
57


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Durkopp Adler 827 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Durkopp Adler 827 in the language / languages: English as an attachment in your email.

The manual is 7,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Durkopp Adler 827

Durkopp Adler 827 User Manual - German - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info