613272
14
Zoom out
Zoom in
Previous page
1/48
Next page
3.6 Messerhöhe überprüfen
Regel:
Die Messerspitze wird nur beim Eintauchen in das Material benötigt.
Die Messerspitze darf die Stichplatte während des Schneidvorgangs
nicht verlassen.
ACHTUNG !
Unbedingt darauf achten, dass bei gelüfteten Korb zwischen
Oberfadenschere und Messerunterkante ein Abstand von mindestens
1 mm besteht.
Hinw eis !
Wird ein Messer nachgeschliffen, wird es in seiner Länge kürzer.
Beim Einsetzen des nachgeschliffenen Messers muss die Messerhöhe
gegebenenfalls korrigiert werden.
Einstellung:
Stoff unter die Klammer positionieren und Nähvorgang starten.
Nähvorgang, während des Aufschneidvorganges auf der
Rückraupe, durch zurücktreten des Pedals unterbrechen.
Stoff etwas unter der Klammer wegziehen, um den Schlitz der
Stichplatte sichtbar werden zu lassen.
Das Handrad solange in Drehrichtung verdrehen bis das Messer in
seiner höchsten Stellung zur Stichplatte steht.
In dieser Stellung soll die Messerspitze 0,2 mm in den
Stichplattenschlitz eingetaucht bleiben.
Justage der Messerhöhe: Schraube 1 lösen.
Das Messer so weit verschieben, bis die richtige Messerstellung
erreicht ist.
Schraube 1 wieder festdrehen.
Schraube 3 lösen.
Anschlag 2 bis an das Messer schieben.
Schraube 3 wieder festziehen.
Durch Zurücktreten des Pedals den Nähvorgang auflösen.
12
3
2
1
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Durkopp Adler 540-100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Durkopp Adler 540-100 in the language / languages: German as an attachment in your email.

The manual is 0,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Durkopp Adler 540-100

Durkopp Adler 540-100 User Manual - English - 48 pages

Durkopp Adler 540-100 User Manual - French - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info