613277
33
Zoom out
Zoom in
Previous page
1/34
Next page
13
2 A
1 A
1
2
12.5 Stop motor setting S359 600045 XXX - EFKA DC 1600/DA82GA
12.5.1 Setting position reader
- set the parameter 170, the display will show Sr1 (reference position)
- depress the pushbutton >>, the display will show PoS 0 and the changing rotation symbol
- turn the hand wheel until the rotation symbol disappears
- turn the hand wheel in such a way, so that the needle point ,when moving downward, is on the level of the throat plate
- depress the pushbutton E and pass to the parameter 171
- set the parameter 171, the disply will show Sr2 (all positions)
- depress the pushbutton >>
- the display will show 1 XXX (value of the bottom position)
- turn the hand wheel, until the value XXX begins to change
- turn the hand wheel at the value of the bottom position angle (160 on the panel)
- depress the pushbutton E
- the display will show 2 XXX (value of the top position)
- turn the hand wheel, until the value XXX begins to change
- turn the hand wheel at the value of the top position angle (460 on the panel)
- depress the pushbutton P 2x (return to the sewing mode)
- tread shortly forward the pedal (memory entry)
12.5.2 Changes of setting parameters of stop motor setting considering original producer setting
Parameter Parameter
No value
111 - Max. revolutions (according to a type of machine)
170 - Reference position
171 1 160 Lower position
2 460 Upper position
190 300 Switch on angle of thread trimmer (210
°)
202 120 Delay of start run after switch off the signal foot
210 200 Stopping time for fancy bar
213 5 Time off full power of backtacking
12.6 Stop motor setting S359 600052 XX - EFKA VD 552/6F82FA
12.6.1 Setting position reader
Positions are set by means of discs with cut outs directly in positon reader.
Setting of the lower position:
- dismount the guard of the position reader
- switch on the mains switch
- tread shortly pedal forward (the machine stops in the needle lower position)
- switch off the mains switch
- turn the beginning of the recess 1 of the overlapping disks in such a way, so that the machine stops with the needle in the
position of 3 mm behind the bootom dead center
- check up in repeating the procedure
Setting of the top position of the thread lever:
- tread the pedal rearward (the machine stops in the needle upper position)
- switch off the mains switch
- turn the beginning of the recess 2 in such a way, so that the machine stops with the thread lever in the top dead centre
- check up in repeating the procedure.
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Durkopp Adler 528 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Durkopp Adler 528 in the language / languages: English as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Durkopp Adler 528

Durkopp Adler 528 User Manual - German - 34 pages

Durkopp Adler 528 User Manual - French - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info