613277

Durkopp Adler 528 Manual

7
Zoom out
Zoom in
Previous page
1/34
Next page
3
6. Operation of the machine
Caution!
Do not use this sewing machine without using the finger guard
(C, Fig. 4) and without the take-up lever guard (P, Fig. 2).
6.1 Upper thread threading (Fig. 1, 2)
Caution!
Before starting the threading operation, switch off the
main switch and put off the feet from the pedals on the
stand to avoid the starting of the machine by treading
the pedal.
After having inserted the bobbin with thread on the thread stand (N), unwind
the thread in sufficient length and pass it through the holes in the thread stand
(N). Direct it then through the thread guide (A) and through the guide (B) - with
the machines without any thread cutter, or through the auxiliary thread tensioner
(L) with the machines provided with such thread cutter. Feed the thread between
the dishes of the tensioner (C). Direct the thread through the adjusting spring
(D) around the guide (E) and through the guide (F) and (G) into the take-up lever
eye (H). From here the thread is directed downward through the guides (F) and
(J) and through the hole of the thread guide (K) on the needle bar towards the
needle eye. Thread the thread into the needle eye from the front (from the sewer)
rearward.
6.2 Winding of thread on the hook bobbin (Fig. 3)
From the thread stand the thread is directed to the tensioner (A) through the
guide (B) on the machine head. From the guide the thread is directed on the
hook bobbin mounted on the shaft (C) of the winder. Wind up the thread
end several times on the bobbin in the clockwise direction and feed it towards
the spring (D). Introduce the thread between the coils thereof and, when
pulling it slightly, cut it with the knife which is mounted inside the spring.
Engage the winder by means of the lever (E). After having wound up the
thread on the bobbin, the winder stops automatically. After having removed
the bobbin from the winder shaft it is possible to cut the thread with the
knife protected by the spring (D) or to cut it with scissors. The thread (A)
serves for regulating the tension of the thread for winding.
6.3 Needle insertion (Fig. 4)
Caution!
Before starting the operation of the needle change, switch off
the main switch and put the feet off the pedals on the stand to
avoid the machine start by treading the pedal.
After having chosen the correct needle thickness (number) corresponding
to the system of the prescribed type (usually the system 134-35), loosen
the screw (A) in the needle holder and insert the needle (B) up to the bottom
of the hole in the needle holder. Turn it in such a way, so that its long groove
is directed ahead (towards the sewer).
Caution - when choosing a thicker needle it is necessary to check, whether
the hook beak does not catch the needle - the eventual setting of the hook
position is to be carried out by a qualified person. Check up, whether the
needle passes through the centre of the needle hole, change a faulty needle.
A
B
G
C
E
K
F
J
H
D
Fig. 1
H
A
L
Fig. 2
B
C
A
E
A
B
Fig. 4
D
Fig. 3
N
M
P
C
OFF ON
MAIN SWITCH
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Durkopp Adler 528 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Durkopp Adler 528 in the language / languages: English as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Durkopp Adler 528

Durkopp Adler 528 User Manual - German - 34 pages

Durkopp Adler 528 User Manual - French - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info