613285
25
Zoom out
Zoom in
Previous page
1/34
Next page
5
Fig. 6
5. Assembly and screwing on of the stand table top
5.1 Assembly of stand table top (Fig. 2, 3, 4, 5)
Put the rubber inserts for placing the machine head into the stand table top into the recess (2 and 3, Fig. 5). For better
fastening, we recomment to stick on the inserts. When mounting the tray (1, Fig. 2) be sure in maintaining the distance “X”
on the whole perimeter of the tray between the interior of the tray and the perimeter of the stand table top recesss (2).
Screw on the main switch (4) on the stand table top (2, Fig. 3).
Fasten the rubber bumper (3, Fig. 3).
Screw on the motor holder (5) according to the Fig. 3 and 4.
Screw on the lighting transformer (6, Fig. 3) for the lighting – if delivered.
Install electric conductors using clamps (8, Fig. 3) Connection differs according to the given motor, supply voltage and
according to the number of conductors of the electric supply. In case of a four-conductor 3 x 400 supply the lighting
transformer must be fed by a separate lead-in cable 1 x 230 V – see par. 12.3.
Screw on the drawer (7, Fig. 3).
In its working and tilted position, the machine head should not be in contact with the tray. The motor pulley diameter must
comply with the maximum prescribed revolutions of the given type of the sewing machine and of the used motor.Adjust the
motor circuit-breaker current according the nominal current given on the motor plate.
5.1.1 Mounting and placing of the machine head on the stand (Fig. 8)
The machine head is in each case supplied with fitted hinges and with a lower cover metal plate meant only for the
machine transport. Do not omit to remove the plate bofore setting the machine head on its stand. Place the machine
head into the stand table top.
Put the supporting pin, which is included in the accessory of the machine, into the hole (7).
Mount the thread guides on the machine head.
5.1.2 Assembly of motor pulley, belt, belt covers (Fig. 6)
Assemble motor pulley (2).
Insert V-belt (3) and tighten it by leaning out of the motor. V-belt is tightened correctly when the opposite sides of belt
are approaching to each other in distance of about 20 mm with power 10 having an effect in the middle of both sides.
Stop motor should be leveled so that the bottom surface of its control panel would be horizontal.
Adjust the stop (4) by bigger pulleys against falling the belt out of the pulley so that the distance from the belt will be
2-3 mm. Adjust pins by smaller pulleys (5) according to the detail (D).
Assemble the bottom cover belt (7) on to the motor.
Assemble upper cover belt (6) by clutch lever motor.
Assemble upper cover belt (6) and position reader by stop motor but only after electrical connection of the head to
the stopmotor.
5
4mm4mm
2-3mm
DETAIL D
5
4
32
6
7
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Durkopp Adler 524 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Durkopp Adler 524 in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Durkopp Adler 524

Durkopp Adler 524 User Manual - German - 34 pages

Durkopp Adler 524 User Manual - French - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info