634041
8
Zoom out
Zoom in
Previous page
1/18
Next page
Element Function
16Separate drive
for edge cutter
Two cutting rpms switchable (only 272-740142)
- Risk of Injury! -
Caution in the area of the edge cutter.
17LED The blinking of the diode shows that the edge cutter
is operationally ready. To switch on and off the
following variants are available:
* Manual via key
* Via the sewing pedal through the run signal of the
sewing drive
* Automatic "On" or "Off" after a selected number of
stitches
* Automatic "Off" after thread trimming (See
Installation Instructions Section 13.)
18Switch for
edge cutting
I = Normal rpm
D = Drive "Off". Knife outside the sewing area
II = Increased rpm for greater stitch lengths and thick
materials
19LED Indicator for main switch "On" (only 272-740142)
20Key Beginning or end bartack on - Bartack off at the
control panel
Beginning or end bartack off - Bartack on at the
control panel
21Key Single stitches
22Key With sewing machine at rest: Needle up-down.
With sewing operation: Bartack (reverse sewing) at
desired position in the seam
23Key Switching the edge cutter on and off. By sub-class
272-640000 the pneumatic operation Z124-401
(optional equipment) must have been installed.
Otherwise the key has no function.
24Key Raise and lower the top feed roller manually.
Automatic lowering after a number of stitches see
Installation Instructions Section 12.
25Knee lever
(only sub-classes -....41)
Before tilting the machine head to the back turn the
main switch off and remove the knee lever. To slip it
out conduct movements 1 and 2 and to hang it back
in movements 3 and 4.
26Hook lubrication The oil reservoir for the hook lubrication should not
drop below the "Min" mark.
By normal operation the oil level should be checked
weekly. Through the fill opening fill Esso SP-NK 10
oil up to the "Max" mark.
The oil flow for the hook lubrication can be regulated
at screw 5.
10
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Durkopp Adler 271 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Durkopp Adler 271 in the language / languages: English as an attachment in your email.

The manual is 2,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Durkopp Adler 271

Durkopp Adler 271 User Manual - German - 18 pages

Durkopp Adler 271 User Manual - Dutch - 18 pages

Durkopp Adler 271 User Manual - French - 18 pages

Durkopp Adler 271 User Manual - Spanish - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info