613253
136
Zoom out
Zoom in
Previous page
1/649
Next page
"Automatic Edge Trimmer" function module
Set the "Automatic Edge Trimmer" function module. Setting value see Parameter
table line A)
After the mains are turned the edge trimmer is activated, the edge knife is up, the
LED X blinks. The blinking of the LED X indicates that an automatic switching on of
the knife during sewing is to occur with a stitch count "z1".
By operating the key Y before starting a seam the edge trimmer is deactivated, the
LED is dark.
A further operation of the key Y before starting a seam will activate the edge
trimmer again and the LED blinks.
The stitch count "z1" for the switching on of the edge trimmer starts with the seam
beginning, the LED blinks.
After completion of the stitch count("z1) the edge trimmer is turned on and the LED
is lit. (Setting value of the stitch counter see Parameter table line B)
If the stitch counter "z1" is set to "0", then the edge trimmer turns on with the first
stitch of the needle.
During the stitch count "z1", the stitch count can be ended and the edge trimmer
immediately turned on through operation of the key Y.
With the activation of the edge trimmer the stitch count("z2") for the turning-off
starts. The LED blinks and thereby indicates that an automatic turning-off of the
edge trimmer is to occur. (Setting value of the stitch counter see Parameter table
line C).
If the stitch counter "z2" is set at "0", then no automatic turning-off of the edge
trimmer occurs.
During the stitch count "z2", the stitch count can be ended and the edge trimmer
immediately turned off through operation of the key Y.
A parameter (Setting value see Parameter table line D) establishes if the next
seam after the thread trimming is conducted with or without edge trimming.
Parameter table for the "Automatic Edge Trimmer" function module
Function Parameters of the controls
DA220C
A "Automatic Edge Trimmer" function module F-250=9
B Number of stitches "z1" for the automatic activation F-253=z1
of the edge trimmer
C Number of stitches "z2" for the automatic turning-off F-254=z2
of the edge trimmer
D With this parameter setting, the edge F-251=1
trimmer is automatically active at the
next seam after the thread trimming
With this parameter setting, the edge F-251=0
trimmer is inactive after thread trimming
GB
27
136


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Durkopp Adler 271 - 274 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Durkopp Adler 271 - 274 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 9,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Durkopp Adler 271 - 274

Durkopp Adler 271 - 274 User Manual - Dutch - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info