633982
38
Zoom out
Zoom in
Previous page
1/48
Next page
2-12
All values must be set like shown in the drawing.
JS jog speed: this function is not used at this machine;
KJ speed factor in POS mode: speed for the smooth-out distance;
KP speed factor in puller mode (1 ... 15): speed factor for the synchronous
operation (1 ... 7 = half step mode; 8 ... 15 = full step mode);
KA acceleration curve of the step motor;
IL holding voltage in home position (1 ... 15): this should reduced to a
minimum to avoid over heating;
IH working voltage (1 ... 15): here you have to consider the
manufacturers information; if the working voltage is set too high, the
motors will be destroyed.
ATTENTION
Damage to the motors due to inadequate settings! Before you modify one of
the values shown here (especially value IH), you should contact the Beisler
service staff.
3.6 Setup page -10
M8
M7
M6
M5
M4
M3M2
M1
F12
F11
F10
F9
F8F7
F6
F5
F4
F3
F2
F1
SETUP
-10
All inputs (F1 ... F12) and outputs (M1 ... M8) are displayed on this page. For
diabled inputs/outputs, the respective icon is crossed out.
At this machine, the output F1, and the inputs M3 ... M6 and M8 must be
disabled. Position the cursor on the icon of an input/output and press the
Plus/Minus key to alter the setting.
The outputs are valves and occupied as follows:
Valve description Output connector
F1 Y1 Lift sewing foot pin 1
F2 Y2 Table blowing pin 3
F2 Y13 Waste evacuation (option with stitch type 515) pin 3
F2 Y16 Tension release for needle thread (option stitch type 515) pin 3
F3 Y3 Contour guiding up and blowing in the contour guiding pin 5
F4 Y4 Contour guiding forward/backward pin 7
F5 Y5 Kett-up pin 9
F6 Y6 Smooth-out device up/down pin 11
F7 Y7 Stacker impulse pin 13
F8 Y8 Transportation unit up/down pin 15
F9 Y9 Top feed adjustment pin 17
F10 Y10 Bottom feed adjustment pin 18
F11 Y11 Mouse backward pin 14
F12 Y14 Drive contour guiding laterally (see below) pin 14
Y15 Stacker up/down (option) pin 12 +24 V pin 19 -24 V
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Durkopp Adler 1281-4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Durkopp Adler 1281-4 in the language / languages: English as an attachment in your email.

The manual is 0,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Durkopp Adler 1281-4

Durkopp Adler 1281-4 User Manual - German - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info