494579

Dual DTFT 27-2 Manual

122
Zoom out
Zoom in
Previous page
1/131
Next page
- 21 -
Sleep Timer Indicator
It is displayed on the upper right of the
screen when a new programme is entered
by digit button or by pressing “P<P”, “-P/CH”,
“P/CH+”, “ ”, “ ” or “ ” button. If sleep
timer is activated it is displayed with the TV
status and erased with it after 3 seconds.
In last minute, sleep timer indicator is dis-
played on the upper right of screen and
stays there until the TV goes automatically
to stand-by.
0:15
Mute Indicator
It is placed in the upper middle of the screen
when enabled, and it stays there until it is
disabled.
To cancel mute, there are two alternatives;
the first one is pressing to "
" button, this
volume is set to the preceding value, and the
second one is increasing the volume level,
thus it starts at the minimum level to in-
crease. By decreasing the volume level in
mute state, mute will not be ignored, only the
volume level will decrease. If mute is can-
celled after decreasing the volume level, the
volume will be valid with the decreased
level.
No-Signal Detection (TV)
If no valid signal detected, it takes 5 minutes
for the switching to the Stand-By mode un-
less any signal detected or no any Remote
Control command is accessed.
After a Remote Control command (if No-Sig-
nal Timer is active) the timer stops and if no
signal detected again the timer is initialized
to 5 minutes and starts 3 seconds later
again to count down.
It is not valid in AV mode.
4:31
No-Signal Detection (PC)
If no valid signal detected for 5 minutes sys-
tem goes to Stand-By mode. To switch on
the system press “
” button.
As the last status feature, system starts from
TV or PC, whichever was the status before
stand-by or switch-off. Note that SCART in-
puts have the precedence on both TV and
PC.
Volume Bar
It is displayed in the lower middle of the
screen. When a volume command is re-
ceived (pressing “
+” or “ -” by Re-
mote Control or Control panel at the top of
the TV) and no menu is active, it stays on the
screen for 3 seconds, after the last volume
command or until another command is re-
ceived in between.
AV Modes
By pressing the “ “ button you can switch
your TV to AV modes (except being in Tele-
text). Pressing this button consecutively will
switch the TV in one of the optional AV
modes: AV-1, AV-2, AV-3, S-VIDEO, PC.
In order to quit the AV mode press the “
”,
digit buttons or “-P/CH” or “P/CH+” .
Signal Out Of Range
When the PC input signal is not supported
by LCD-TFT TV, a message is displayed like
“Signal out of range” and screen is blanked.
If no valid signal detected for 5 minutes sys-
tem goes to Stand-By mode.
ENG-2707W-1543 UK-27 INCH TFT (17MB08)-DUVAR MON-(WO PIP)(CHI MEI-B1).p65 30.05.2006, 16:3621
… 122 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dual DTFT 27-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dual DTFT 27-2 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 8,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info