494553
35
Zoom out
Zoom in
Previous page
1/121
Next page
English - 34 -
Installing the Batteries to the Remote
1. Lift the cover on the back of the remote upward
gently.
2. Install two AAA batteries. Make sure to match the +
and - ends of the batteries in the battery compartment
(observe the correct polarity.
3. Replace the cover.
Connect Power & Antenna/Cable
IMPORTANT: The TV set is designed to operate on
220-240V AC, 50 Hz socket. After unpacking, allow
the TV set to reach the ambient room temperature
before you connect the set to the mains. Plug the
power cable to the mains socket outlet.
SPDIF
VGA
Aerial or Cable
Switching On/Off
To Switch the TV On
Connect the power cord to the 220-240V AC, 50
Hz socket.
Switch the
button on the rear left hand side
to position “|” so the TV will switch to standby mode.
Then the standby LED lights up.
To switch on the TV from standby mode either:
a. Press the
button, CH ^ / v or a numeric button
on the remote control.
b. Press the middle of the “
” button on the TV.
By either method the TV will switch on.
Switching the TV Off
Press the button on the remote control or press
the
button, so the TV will switch to standby
mode.
Switch the “
” button to position 2 as illustrated,
so the TV will switch OFF.
To turn off the TV completely, remove the power
cord plug from the mains power socket.
Note: When the TV is switched to standby mode,
standby LED can blink to indicate that features such as
Standby Search, Over Air Download or Timer is active.
The LED can also blink when you switch on the TV from
standby mode.
First Time Installation
When turned on for the rst time, the language
selection” menu appears. The message Welcome
please select your language! is displayed in all
language options listed alphabetically.
Press the or button to highlight the
required language, press OK button to select. “First
Time Installation” appears. Use “
” or “ ” button to
set the required country, and press button to
select Search Type (optional).
Use
or to set the desired search type. Available
search types are Digital and analog, digital only and
analog only.
When set, press
to select Teletext Language.
Use
or to select the desired Teletext Language.
Next, select Scan Encrypted and set as Yes if you
want to scan coded stations.
Press OK button on the remote control to continue
and the following message will be displayed on the
screen.
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dual 22970 LED at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dual 22970 LED in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 29,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info