695320

DRU STYLE 4-01 Manual

14
Zoom out
Zoom in
Previous page
1/64
Next page
(10) stick through the clamps (11). Attach screw nuts and
washers to the bolts (10) and tighten closely up to the
stop. Then slide the screw spindle (12) into the clamp
(13). Fix the screw nut and washer to the screw spindle
(12) and tighten until the interior is standing parallel to the
wall.
N.B. If easy accessible, e.g. on the ground floor, the out-
let pipe can also be mounted from the outside after the
grid interior sheet and the basket have been disassembled.
STYLE 4-01 and 5-01:
After fitting heat-exchanger fix thermostat phial in clip
provided at rear of backplat (R.H.S.).
Connection of the gas supply
For the different types are the connections as mentioned
below:
• STYLE 3-01 3/8” inner thread
• STYLE 4-01, 5-01 3/8” outer thread
If the supply pipe enters the appliance through the back
plate, press out the disc in the plate. An approved con-
necting tap with coupling should be used in the supply
pipe (For Belgium this should be B.G.V. approved). The
connecting tap with coupling should be fitted outside the
casing. Furthermore:
• Expel all air from the supply pipes/hoses before coupling
to the appliance.
• Do not turn the coupling tap when connecting it to the
gas supply.
• Avoid any pressure on the control tap and pipes.
• Check that all connections are gastight.
Operations
The manufacturer has made the appliance suitable for
the type of gas as indicated on the type identification tag.
Check that the gas pre-pressure and burner pressure cor-
respond with what is stated on the type plate. If necessary,
use the control screw to correct the burner pressure.
The control screw for burner pressure is located behind
the cover on the gas control. This cover can be removed
by removing the screw and clicking loose the lip on the
left side by means of a screwdriver. The thermostat
regulates modulatingly between “full power setting” and
“low power setting” and , when little heat is required, in
two settings, i.e. “low” or “off”. In this situation, the pilot
light keeps burning. The “low” setting can only be checked
when the room temperature is higher than
± 15°C (60°F).
The low setting
The low setting has been adjusted to ± 20% of the full
consumption. The low setting screw has been fully tight-
ened and is supplied with the correct low setting bore.
This is not adjustable.
Pilot light burner
Upon delivery, the pilot light burner has the correct con-
sumption by means of a nozzle inside the pilot light burner.
The pilot light burner needs no adjustment.
Putting the casing in its place
From the top, hang the casing over the back sheet, taking
care that the hooks of the casing fit into the notches of
the back sheet and that the operating buttons fit into the
appropriate opening in the casing.
12
INSTRUCTIONS FOR INSTALLATION
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DRU STYLE 4-01 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DRU STYLE 4-01 in the language / languages: English, German, Dutch, French, Italian, Spanish, Norwegian as an attachment in your email.

The manual is 1,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info