7.5 Placing the control hatchA number of components are placed in the control hatch, such as data plate, gas control and, if applicable, components belonging to the DRU Powervent System®.The control hatch was designed in such a way, that all components as well as adjustment, measurement and regulating provisions are within optimum reach and the components work optimally. A control hatch placed and furnished on the side of the chimney breast ensures an optimum transmission and reception strength of the remote control and receiver. The control hatch also ensures sufficient aeration of the chimney breast. For that reason, the use of a control hatch is not without significance. Not using a control hatch could may void the warranty.3-The bottom of the control hatch may not be placed higher in the appliance than the burner surface.-Place the control hatch and bracket with gas control only indoors, on a dry spot!Place the control hatch as follows (see fig. 7-15):1Make an opening in the chimney breast as described in the manual for the control hatch (1).2The opening in the chimney breast may be made horizontal and vertical.1Place the inner frame. For this, first remove the outer frame with door (2).3The inner frame should be placed in the correct way. Two positions are possible. Placing the inner frame with a rotation of 180° is not allowed.2When the chimney breast is made of bricks, the inner frame can be built with bricks at the same time.In case of a different material, the inner frame can be glued or fastened with four countersunk screws.1Fix the outer frame with door (3) to the inner frame using two Allen screws.2The outer frame can be placed in such a way that the door turns to the left or right.1Attach the bracket with gas control to the inner frame. Proceed as follows:-Unwind the cables. This will, amongst other things, prevent a poor operation of the ignition (4).-Unwind the flexible gas pipe(s).-Mount the bracket with gas control to the inner frame. The slotted hole falls in Allen screw; the hole at the bottom falls over the head of Allen screw.-Fix the bracket with Allen screw.3-Avoid kinks in the pipes (4).-Do not lay the cables of the ionisation pin and spark electrode along metal parts, wiring and other components.1Connect the gas pipe with gas tap (6) (also see section 6.3).1Bleed the gas pipe (7).2If the gas tap is closed, the bracket with gas control can be easily removed by loosening the clamp coupling under the gas control and loosening the Allen screw (C) by a few turns. The bracket with the gas control can now be lifted and removed towards the front out of the control hatch.1Place the data plate in its intended clamp (8).1Connect the 230V mains voltage with protective earth using the correct type of plug. The other side of the power cable can be easily connected to the universal 230V plug in the control hatch. Use this universal 230V plug to disconnect the appliance from the power supply, if necessary.3If the 230V power cable is damaged, replace it by a similar power cable or a power cable that is available from your dealer.3Always close the control hatch with the lock (10), because of the electricity behind the door (230V). The lock is operated by means of a fitting flat object.Installation manual36
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for DRU Maestro 80-3 RCH at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of DRU Maestro 80-3 RCH in the language / languages: English as an attachment in your email.
The manual is 7.09 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
