Installation manual63MalfunctionsError codeF12F13/F14F15 F15(PowerVent®)F16F17ProblemESYS is not released(no ionisation). Flame Loss when only the main burner (F13) is on or both burners (F14) are onNo burner device (see "C" in appendix 3, fig. 38)High limit errorFan doesn't start, appliance doesn't sparkFan starts, appliance doesn’t sparkHardware Error ESYS3 subsequent, unsuccessful ignition cyclesPossible causeESYS is in hard-lockIonisation pin short-circuitedIonisation current too critical(0.8 ≤ ionisation < 1.8 μA)Suffocation due to poor flue gas channelSuffocation when using PowerVent®24 hour check control(only in case of F13)Gas has fallen awayGas control defective (see "A" in appendix 3, fig. 38)Burner device came looseBurner device incorrectly mountedPins on the connector on the gascontrol are bentHigh limit bridge defectiveFan defectiveDiff. pressure hoses leakDiff. pr. sensor defectiveCtrl signal cable defectiveConcentric system defective and/or leakingESYS defective (burner device)Premature interruption ignition cycle, also see F08RemedyWait half hour until ESYS resets itselfRemove chips, vermiculite or glowmaterial lying against the ionisation pinIncrease ionisation current to≥ 1.8 μA by rearranging vermiculiteand removing chips and dust from the burner openingsCheck the concentric systemCheck the setting of the applianceCheck the pressure setting of the PowerVent® systemReset with remote control (consult PowerVent® manual)Check gas supplyReplace the gas controlAttach the burner deviceMount the burner device correctlyBend them straightCheck High limit bridge ESYSReplace fanCheck connections and hosesReplace/repairReplace diff. pr. sensorReplace control cableCheck concentric system for leaks and defectsRepair/replaceReplace ESYS (burner device)After 30 min. F17 can be reset w. mains voltage on appliance, see F08
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for DRU Maestro 80-2 RCH at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of DRU Maestro 80-2 RCH in the language / languages: English as an attachment in your email.
The manual is 7.09 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
