810253
48
Zoom out
Zoom in
Previous page
1/56
Next page
10. Final inspection
For a good and safe operation of the appliance, the following checks must be performed prior to commissioning.
10.1 Gas tightness
3All connections must be gas tight. Check the connections for gas tightness. The gas control can be subjected to a
maximum pressure of 50 mbar.
10.2 Gas pressure/line-pressure
The burner pressure is set at the factory; see data plate.
3The line-pressure in house installations must be checked, because it can be wrong.
1Check the line-pressure. See fig. 6-1 (P1) for the measuring nipple on the gas control.
- Contact the gas company if the line-pressure is too high.
- If the line-pressure is too low, check this at the gas meter. Contact the gas company if the line-pressure is also too low
at the gas meter.
10.3 Ignition main burner
For igniting the main burner, see the User Manual.
10.3.1 First ignition of the appliance after installation or adjustments
3After installation, or after work has been performed, you should ignite the appliance for the first time without the glass
pane. If necessary, bleed the gas pipe.
Proceed as follows:
1. Remove the glass pane from the appliance (see chapter 8).
2. Start the ignition procedure as described in the User Manual.
The appliance ignites on the main burner with 50% of the full output. Once the flame has passed over the main burner to
the ionization and a flame has been detected, the appliance will modulate to 100%. This detection will have to take place
within 15 seconds, or else the appliance will enter error mode. If the appliance has a second, separately switchable burner
and the main burner continues to burn, the second valve will switch in order to ignite the second burner. Here, you can
hear a clear ‘click’ sound. (Go to step 11 if the burner continues to burn).
If the main burner does not ignite:
3. Reset the system by pressing the buttons ‘arrow up’ and ‘arrow down’ simultaneously.
4. Repeat the ignition procedure until the main burner ignites.
3The system can be reset and re-ignited two times in a row at maximum. Then the system will enter a hard lock-out and
you will have to wait half an hour, before you can make a new attempt. Never use more than 3 attempts to ignite the
appliance, as this could lead to a accumulation of gas within the appliance. Make sure that there is no
more gas in the appliance before making 3 new ignition attempts.
1If you do not succeed after a few attempts, consult the diagram with error messages (see appendix 1: Malfunctions).
5. Check the flame transfer on the main burner and check whether the main burner continues to burn (go to step 11 if the
burner continues to burn).
If the main burner does NOT continue to burn:
6). Mount the glass pane.
7). Reset the system by pressing the buttons ‘arrow up’ and ‘arrow down’ simultaneously.
8). Now ignite the main burner and check whether it continues to burn (go to step 12 if the burner continues to burn).
3Limit the ignition attempts with mounted glass pane to a MAXIMUM of 1 ignition attempt.
If the main burner again does NOT continue to burn:
9). Switch off the appliance.
10). Consult the diagram with error messages (see appendix 1: Malfunctions) (Go to step 1 once the malfunction has been
remedied).
Installation manual
48
48


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DRU Maestro 75 Tunnel at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DRU Maestro 75 Tunnel in the language / languages: English as an attachment in your email.

The manual is 14.21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DRU Maestro 75 Tunnel

DRU Maestro 75 Tunnel User Manual - German - 56 pages

DRU Maestro 75 Tunnel User Manual - Dutch - 56 pages

DRU Maestro 75 Tunnel User Manual - French - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info