810253
35
Zoom out
Zoom in
Previous page
1/56
Next page
Installation manual
35
1Identify logs A to K (see fig. 8-9).
2- Use the burn stains on the logs for identification.
- In the overview photograph, the side glass pane is located on the right side.
1Place log A over the lying burner in the positioning brackets (see fig. 8-20).
1Place log B on the left side behind log A, in the two positioning brackets and on log A.
1Place log C on the right side behind log A, in the positioning bracket and on log A, make sure there is 1 centimetre play
between log C and the standing burner to the right (see fig. 8-20).
1Place log D in the positioning bracket to the right and on log C.
1Place log E against the tube of the standing burner to the right and in the positioning bracket.
1Place logs F and G in front of the lying burner, in the positioning brackets.
1Place log H against the tube of the standing burner to the left and in the positioning bracket.
1For appliances without LEDs, use all chips in the wood set.
1Fill the vermiculite plates with chips, spread the chips evenly, keep the sections marked in red free of chips (see fig. 8-18).
1For appliances with LEDs, use the glow rocks, coals and a portion of the chips.
1Only use 400ml of the supplied grey chips and 800ml of the black chips. This is less than the total ammount supplied with
the appliance. Dispose of the surplus chips according to local laws.
2First place the glow rocks and then the coals. Switch on the glow lighting while placing, so that the stray light can be
seen directly and covered with the rocks and coals.
1Spread the glow rocks over the grid pattern and square holes in the vermiculite plate, keep the sections marked in red
free (see fig. 8-19).
1Spread the chips over the remaining sections, keep the sections marked in red free.
LED appliances have a different type of base covering to appliances without LEDs.
3- The vermiculite plates are provided with square holes, which ensure air supply. Do not place more than one layer of
base covering over these holes.
- Ensure that the base covering does not enter the slot for the glass pane.
2Place chips on the edge of he pane frame. Prevent chips from getting under the pane frame (see fig. 8-17).
1Place log I on the left side in front of log A, in the positioning bracket and on log A.
Make sure there is 1 centimetre play between log I and the standing burner to the left (see fig. 8-23).
1Place log J over the standing burner to the left, make sure the recess falls over the burner properly.
1Place log K over the standing burner to the right, make sure the recess falls over the burner properly.
2Spread the ash over the chips and/or place the glow material over the lying burner in separate tufts.
3- Prevent the ash from ending up on the burners.
- Only place the glow material on sections that are marked green.
- The areas around the ionization and ignition should remain free from glow material (see fig. 8-15).
- The glow material may affect the colour of the flame picture.
8-14
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DRU Maestro 75 Tunnel at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DRU Maestro 75 Tunnel in the language / languages: English as an attachment in your email.

The manual is 14.21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DRU Maestro 75 Tunnel

DRU Maestro 75 Tunnel User Manual - German - 56 pages

DRU Maestro 75 Tunnel User Manual - Dutch - 56 pages

DRU Maestro 75 Tunnel User Manual - French - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info