8 Appliance8.1 Glass panesThe glass pane of this appliance is to open to allow cleaning of the inside of the pane. Before installing the wood set, adjusting the appliance or maintenance, the glass pane must be removed.3-Avoid damaging the pane during removal/placing.-Use the socket spanner supplied for loosening and tightening the self-tapping screws.-Avoid/remove fingerprints on the glass pane, as they will burn into the glass.8.1.1 Removing the side paneProceed as follows to open the glass pane (see fig. 8-1).3Only open the glass pane if the appliance is turned off and is at room temperature.3Make sure you do not damage the glass pane.1Take the springy glass pane strip at its handles and place it on the higher brackets.1Grab the glass pane at both sides, tilt the top of the glass pane a little away from the appliance and lift up the glass pane at an angle.1Tilt the bottom of the glass pane away from the appliance and remove the glass pane.8.1.2 Removing the front pane/rear pane.Proceed as follows to open the glass pane (see fig. 8-2).3Only open the glass pane if the appliance is turned off and is at room temperature.3Make sure you do not damage the glass pane.1The side pane must be removed first (see section 8.1.1).1If applicable, slide the lower decorative strip away from the appliance. It is not necessary to remove it.1Grab the vertical decorative strip at the top, tilt the vertical decorative strip and remove it.1Unscrew the self-tapping screws from the vertical glass strip and remove the vertical glass strip.1Unscrew the self-tapping screws from the upper glass strip and remove the upper glass strip.1Place the suction cup on the front glass pane.1Grab the glass pane at the suction cup and side and slightly tilt the top away from the appliance.1Tilt the glass pane and move it sideways.1Tilt the bottom of the glass pane away from the appliance and remove the glass pane.8.1.3 Placing the glass paneOnly replace the glass pane once it has been cleaned. Proceed as follows to close the glass pane. Placing the glass pane will take place in reverse order of removing the glass pane, as described in 8.1.1 and 8.1.2 (see fig. 8-1 and 8-2):3-Make sure that the pane frame is free of dirt before the glass pane is placed.-Avoid/remove fingerprints on the glass pane, as they will burn into the glass.-Do not overtighten the self-tapping screws, in order to prevent breaking and/or stripping the thread.-Place the glass pane with the logo in the bottom right corner.3Make sure the front and rear glass pane is in full contact with the side pane (there may be no opening between the panes).If the front, rear and side glass panes do not connect:1Loosen the self-tapping screws of the glass pane's front and rear glass strips by a few turns.1Slide the front and rear glass panes tightly against the side glass pane.3Make sure there is no sealing tape between the front, rear and side panes (where the panes connect).1Tighten the self-tapping screws of the glass strips.Installation manual30
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for DRU Maestro 75 RCH at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of DRU Maestro 75 RCH in the language / languages: English as an attachment in your email.
The manual is 5.63 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
