571624
8
Zoom out
Zoom in
Previous page
1/44
Next page
English
INSTALLATION MANUAL
!Caution
Use non combustible and heat-resistant materials for the chimney breast including the top of the chimney
breast, the material in the chimney breast and the back wall of the chimney breast.
The appliance is not a support structure. Make sure the appliance does not have to bear the weight of the
chimney breast for example.
The passage of the ventilation holes (outgoing), which are placed as high as possible, is stated in Appendix 2,
Table 2.
If no control hatch is placed in the chimney breast, an air supply of at least 80 cm 2 should be attached as low
as possible. If there is, the control hatch will suffice as air supply.
!Caution
When placing the chimney breast, you should take the following into account (see Appendix 3, Fig. 2):
The location for the control hatch: this must be placed as low as possible.
The dimensions of the control hatch; see Placing the control hatch section 5.7.
The location of the ventilation holes (V) (outgoing).
Maintain a minimum 30 cm distance between the top of the ventilation hole (outgoing) and the ceiling of the
house.
The measurements of the glass pane, so that it can be placed/removed after placing the chimney breast.
The protection of the gas control and the pipes against cement and plaster.
If possible, you should place decorative strips, frames, etc., after any required structural work has been
completed. Prevent the use of painter's tape. If this is not possible: use a good quality painter's tape and
remove it immediately after plastering or painting work.
!Tip
You should preferably apply the ventilation holes (outgoing) on both sides of the chimney breast. Use the DRU
ventilation elements.
Check the following issues, before the chimney breast is fully closed:
Whether the discharge / concentric system is placed correctly.
Whether the channels, fixing brackets and possible clip bindings, which cannot be reached after installation,
are fastened by means of self-tapping screws.
Ø
Do not plaster on or over the edges of the construction frame, because:
The heat of the appliance could cause cracks.
It will no longer be possible to remove/place the glass pane.
Ø
When using stone-like materials and/or plaster finishing, allow the chimney breast to dry for at least six weeks
prior to taking the appliance into operation in order to prevent cracks.
5.7 Placing the control hatch (if applicable)
The control hatch (also see paragraphs 5.5 and 5.6) is placed as low as possible in the chimney breast.
!Caution
The bottom of the control hatch may not be placed higher in the appliance than the burner surface.
Place control hatch and bracket with gas control indoors in a dry place only!
A number of components are placed in the control hatch, such as data plate, gas control and, if applicable, the
components belonging to the DRU Powervent System ®.
Place the control hatch as follows, see Appendix 3, Fig. 3 for details:
Ø
Make an opening in the chimney breast, as described in the manual for the control hatch.
!Tip
The opening in the chimney breast may be made horizontal and vertical.
Ø
Place the inner frame (A); unscrew bolts (D and F) for this.
!Caution
The inner frame should be placed in the correct way. Two positions are possible. Placing the inner frame with a
rotation of 180° is not allowed (see Appendix 3, fig. 4).
!Tip
When the chimney breast is made of bricks, the inner frame can be built with bricks at the same time.
In case of a different material, the inner frame can be glued or fastened with four countersunk screws.
Ø
Remove the bracket with the gas control (B) from the appliance and place these self-tapping screws back in the
appliance.
8
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DRU Lugo 80 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DRU Lugo 80 in the language / languages: English as an attachment in your email.

The manual is 4.96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DRU Lugo 80

DRU Lugo 80 User Manual - English - 28 pages

DRU Lugo 80 User Manual - German - 28 pages

DRU Lugo 80 Installation Guide - German - 44 pages

DRU Lugo 80 User Manual - Dutch - 28 pages

DRU Lugo 80 Installation Guide - Dutch - 44 pages

DRU Lugo 80 User Manual - French - 28 pages

DRU Lugo 80 Installation Guide - French - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info