Manual DRU Lugo 70 (page 19 of 44) (English)

571623

Zoom out

Zoom in

1/44

English

INSTALLATION MANUAL

!Tip

When checking whether the main burner continuous to burn, it is possible that it switches off after 15 seconds. In

that case, this will be caused by the fact that there is no ionization detection and because the glass window has

not been placed. This can be regarded as a situation where the main burner continues to burn.

!Caution

• Always wait 5 minutes before re-igniting the appliance.

• No changes may be made to the gas control.

7.3.2 Main burner

!Caution

• The ignition electrode should ignite the main burner within a couple of seconds and without popping.

• The main burner(s) must cross the full burner smoothly and without popping and continue to burn.

• If the appliance does not ignite after three restarts and enters hard lockout, it may never be reset by

disconnecting it from the power supply. If a restart is necessary after all: remove the glass pane and make sure

the gas is able to escape from the appliance. After this, the appliance may be disconnected from the power

supply for 10 seconds. After these 10 sec., the power supply may be reconnected. Ignite the appliance in the

same way as the first ignition, as indicated in section 7.3.1.

Check operation of the main burner from a cold condition.

If sparks are determined between the ignition electrodes, the main burner should burn within a few seconds.

!Tip

The flame picture and a good flame transfer can only be properly judged if the glass window is installed.

Use the malfunction search diagram (Appendix 1) if the ignition of the main burner does not comply with the

above-mentioned requirements.

7.4 Flame picture

The flame picture can only really be assessed when the appliance has been burning for several hours. Volatile

components from paint, materials, etc., which evaporate in the first hours, will affect the flame picture.

Check whether the flame picture is acceptable.

Consult the malfunction search diagram (Appendix 1) if the flame picture is not acceptable, in order to solve the

problem.

8. Maintenance

Once per year, the appliance must be checked, cleaned and, if necessary, repaired by a competent installer in the

field of gas heating and electricity. Check at least whether the appliance is working properly and safely.

!Caution

• Close the gas tap when performing maintenance work.

• Check the gastightness after repair.

• Make sure there is no voltage on the appliance.

• SS-absolutely do not clean the concentric system (internally) with a steel brush or metal sponge, for example.

This will damage the oxide skin and could lead to leaks in the system as a result of pitting corrosion.

Clean glass pane(s), if necessary.

!Caution

Only clean a glass pane once it has reached room temperature.

Caution!

• Avoid damage to the glass pane(s).

• Avoid/remove fingerprints on the glass pane(s), as they will burn into the glass.

• Clean the pane(s) as described in the user manual.

• Regularly remove accumulated dirt, as it can burn into the glass.

• Do not use the appliance when a pane is broken and/or cracked, until it has been replaced as described from

section 5.10.

!Caution

If necessary, place back the wood or pebble set correctly; for this, see from section 5.10.

Inspect the flue gas discharge system.

!Caution

You must always perform a final inspection.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DRU Lugo 70 in the language / languages: English as an attachment in your email.

The manual is 4.96 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DRU Lugo 70

DRU Lugo 70 User Manual - English - 28 pages

DRU Lugo 70 User Manual - German - 28 pages

DRU Lugo 70 Installation Guide - German - 44 pages

DRU Lugo 70 User Manual - Dutch - 28 pages

DRU Lugo 70 Installation Guide - Dutch - 44 pages

DRU Lugo 70 User Manual - French - 28 pages

DRU Lugo 70 Installation Guide - French - 44 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DRU Lugo 70 Manual

Product: