571623
14
Zoom out
Zoom in
Previous page
1/44
Next page
English
INSTALLATION MANUAL
5.14.2 Removing the side glass pane
The side glass panes should be removed in case of torn or broken panes:
Ø
Remove the front glass pane; see section 5.14.1;
Ø
Remove the screws from the vermiculite tray and remove it;
Ø
Loosen the nuts of the bottom glass strip on the inside of the appliance by a few turns;
Ø
Unscrew the allen bolt from the vertical decorative strip;
Ø
Grab the vertical decorative strip at the top, tilt the vertical decorative strip and remove it;
Ø
Unscrew the self-tapping screws from the vertical glass strip and remove the vertical glass strip;
Ø
Unscrew the self-tapping screws from the upper glass strip and remove the upper glass strip;
Ø
Grab the pane at the side and slightly tilt the top towards you;
Ø
Lift the glass pane and move it towards the side (you are now located at the side of the appliance);
Ø
Tilt the bottom of the glass pane towards the front and remove the glass pane.
5.14.3 Placing the glass pane
Placing the glass pane will take place in reverse order of removing the glass pane, as described above:
!Caution
Avoid/remove finger prints on the glass pane, as they will burn into the glass;
The self-tapping screws should not be over-tightened, since otherwise they could break or strip the thread;
Place the glass pane with the logo at the bottom right.
!Caution
Make sure the front glass pane makes full contact with the side pane (there may be no opening between the side
pane and front pane).
If the front and side glass panes do not connect:
Ø
Loosen the self-tapping screws of the side pane clamp strips by a few turns;
Ø
Slide the side pane tightly against the front pane;
!Caution
Make sure there is no sealing tape between the front and side panes (where the panes connect).
Ø
Tighten the self-tapping screws and nuts of the clamp strips.
5.15 Setting the appliance
The appliance has to be set in such a way that it works correctly in combination with the used concentric system.
For that purpose, a restrictor slide is placed and/or the air inlet guide is removed. The conditions for application
with wall terminal and roof terminal are stated in appendix 2, tables 4, 5 and 6.
This appliance is suitable for PowerVent®. For more information, see the PowerVent® installation manual.
5.15.1 Restrictor slide (R)
The restrictor slide (R) is supplied separately.
It is mounted as follows (see appendix 3, fig. 8):
Ø
Unscrew the 2 pre-mounted self-tapping screws (U) from the appliance;
Ø
Place the restrictor slide (R) with the 2 self-tapping screws (U). The restrictor slide (R) falls over part of the exhaust
pipe hole, do not tighten the self-tapping screws (U);
!Caution
When fastening, the arrow on the restrictor slide should point away from you.
Ø
Adjust the position of the restrictor slide (R) using situations B to E in appendix 2, table 6. The letter for the
restrictor slide position corresponds with the letter of the situation in table 6;
Ø
Make sure the point of the triangle belonging to the position that you want and the centre of the self-tapping
screw are exactly aligned;
Ø
Tighten the 2 self-tapping screws (U).
5.15.2 Air inlet guide (L)
At the back of the appliance, below the vermiculite tray, the air inlet guide (L) is placed. The air inlet guide can be
reached by removing the vermiculite tray. At delivery, the air inlet guide is placed. When removing the air inlet
guide, proceed as follows (see appendix 3, fig. 9):
Ø
Unscrew the self-tapping screws from the vermiculite tray (B) and remove the tray;
Ø
Remove the self-tapping screws from air inlet guide and remove the air inlet guide from the appliance.
!Caution
Place back the self-tapping screws back in the appliance.
Ø
Place back the vermiculite tray (B) and fasten the tray with the self-tapping screws.
14
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DRU Lugo 70 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DRU Lugo 70 in the language / languages: English as an attachment in your email.

The manual is 4.96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DRU Lugo 70

DRU Lugo 70 User Manual - English - 28 pages

DRU Lugo 70 User Manual - German - 28 pages

DRU Lugo 70 Installation Guide - German - 44 pages

DRU Lugo 70 User Manual - Dutch - 28 pages

DRU Lugo 70 Installation Guide - Dutch - 44 pages

DRU Lugo 70 User Manual - French - 28 pages

DRU Lugo 70 Installation Guide - French - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info