Manual DRU GLOBAL 70 XT (page 31 of 60) (English, Dutch)

528138

Zoom out

Zoom in

1/60

English

INSTALLATION MANUAL

Global 70 / 70 XT

discharge/combustion air supply system, hereafter referred

to as the concentric system.

The passage to the outside can be made with a wall termi-

nal (see section 6.5.2) or a roof terminal (see section 6.5.3).

If necessary, you can also use an existing chimney (see

section 6.5.4).

- Only use the concentric system supplied

by DRU (Ø100 / Ø150 mm). This system

has been tested together with the ap-

pliance. DRU cannot guarantee a proper

and safe operation of other systems and

does not accept any liability for this;

- For connecting to an existing chimney

you should only use the chimney kit sup-

plied by DRU.

The concentric system is constructed from (the connection

stump of) the appliance.

If structural circumstances require that the concentric

system is placed ﬁ rst, the appliance can later be connected

with a telescopic pipe piece.

6.5.2 Application with wall terminal

6.5.2.1 Construction of concentric system with wall

terminal

The concentric system with wall terminal has to comply

with the following conditions:

- First, a concentric pipe of at least 1 meters should be

connected vertically to the appliance;

- The total vertical pipe length may have a maximum of

4 meters;

- A 90° bend is connected to the other end of the vertical

part;

- When using a minimum of 1 meter up to a maximum of

4 meters of vertical pipe length, the total horizontal pipe

length can have a maximum of 3 meters (excluding wall

terminal, see ﬁ g. 3a and ﬁ g. 3b).

Depending on the construction of the concentric system,

the appliance must receive further settings; see Table 1 for

determining the conditions and section 6.8, Adjusting the

appliance, for the method.

6.5.2.2 Placing concentric system with wall

terminal

- Maintain a distance of at least 50 mm

between the outside of the concentric

system and the walls and/or the ceiling.

If the system is built in (for instance) a

cove, it should be made with non com-

bustible material all around it.

- Use heat-resistant insulation material

when passing through combustible

material;

- The rosette (mounting inner plate) of

the wall terminal is too small to seal

the Ø 250 mm opening when passing

through combustible material. That is why

you should ﬁ rst apply a sufﬁ ciently large

heat-resistant intermediate plate to the

wall. Then, the rosette is mounted on the

intermediate plate.

!Caution Some heat-resistant insulation materials

contain volatile components that will

spread an unpleasant smell for a prolon-

ged time; these are not suitable.

Place the concentric system as follows:

• Build the system up from (the connection stump of) the

appliance.

• Connect the concentric pipe pieces and the bend.

• On each connection, apply a clip binding with silicon sea-

ling ring.

• Use a self-tapping screw to ﬁ x the clip binding to the pipe

on locations that cannot be reached after installation.

• Apply sufﬁ cient clamps, so that the weight of the pipes

does not rest on the appliance.

• Determine the remaining length of the wall terminal;

• Make sure the wall terminal has the right dimensions.

Caution

Table 1: Conditions for the adjustment of the appliance with a wall terminal

G20/25

Total Total number See Air inlet guide Bafﬂ e Distance

number of of meters ﬁ gure of

meters horizontal restriction

vertical pipe length in mm

pipe length (excluding

wall terminal)

1 - 4 >0 - 3 3a NO NO OPEN

1 - 4 0* 3b YES NO OPEN

* factory setting

Caution

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DRU GLOBAL 70 XT in the language / languages: English, Dutch as an attachment in your email.

The manual is 7,1 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DRU GLOBAL 70 XT

DRU GLOBAL 70 XT User Manual - English - 20 pages

DRU GLOBAL 70 XT User Manual - German - 20 pages

DRU GLOBAL 70 XT User Manual - Dutch - 20 pages

DRU GLOBAL 70 XT User Manual - French - 20 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DRU GLOBAL 70 XT Manual

Product: