571712

DRU GLOBAL 70 X Manual

47
Zoom out
Zoom in
Previous page
1/60
Next page
English
45
USER MANUAL
Global 70 / 70 XT
Ignite the appliance as follows:
• Set button A on the gas control to ON (button B is
controlled automatically) (see fi g. 4).
The gas control is located in the control box.
• Simultaneously press the buttons OFF and (large fl ame)
on the remote control.
• Let go of the buttons when a short sound signal indicates
that the ignition process has been started.
In succession:
- the continuous signals will indicate that the ignition
process is active;
- a short sound signal will indicate that the ignition process
has fi nished;
- the appliance will automatically switch through to the
highest position of the main burner, which will start to
burn in a few seconds.
- If the pilot burner is not burning after
3 ignition attempts, you must close the
gas tap and call the installer;
- When igniting the pilot burner, you will
hear sound signals. After the last short
sound signal, the main burner should be
largely ignited within about 10 seconds.
If this is not the case, you must close the
gas tap and warn your installer;
- If the appliance ignites with a pop sound,
you must close the gas tap and contact
your installer.
!Tip A little motor will start to run when the
main burner operates, you will be able to
hear it.
4.2.2.2 Flame height / standby
The fl ame height can be adjusted continuously by using the
buttons (small fl ame) and (large fl ame). By continuing
to lower the fl ame height, the appliance can be set to the
standby position; this means that only the pilot burner will
still be burning.
• Press button (small fl ame) to lower the fl ame height
and/or to set the appliance in the standby position.
• Press the button (large fl ame) to raise the fl ame height
and/or to switch on the main burner from the standby
(pilot burner) position.
- If you continue to press down button
(large fl ame) on the remote control, the
main burner should be largely ignited
within about 10 seconds. If this is not the
case, you must close the gas tap and warn
your installer;
- If the appliance ignites with a pop sound,
you must close the gas tap and contact
your installer.
4.2.2.3 Switching off
Switch the appliance off by pressing the OFF button.
The pilot burner will also go out.
4.2.3 Temperature display
The room temperature can be indicated on the display
in degrees Celsius (ºC) using a 24 hour clock or degrees
Fahrenheit (ºF) using a 12 hour clock.
• Simultaneously press OFF and
(small fl ame), until the
correct display appears.
4.2.4 Time
The display can indicate time.
After placing the battery or simultaneously pressing
(large fl ame) and (small fl ame), the time indication will
fl ash on the display and you will be able to adjust the time.
• Simultaneously press and until the time indication
fl ashes on the display.
• Press the button (large fl ame) to set the hours.
• Press the button (small fl ame) to set the minutes.
• Press OFF to return to the MAN position, or wait for the
system to automatically return to the MAN position.
4.2.5 Thermostat function
Using the thermostat function you can set two temperatu-
res, which can be controlled thermostatically.
These temperatures are referred to as day temperature
and night temperature.
The ✹ TEMP and TEMP symbols on the display refer to
day and night temperature respectively.
The room temperature is compared to the set day/night
temperature and then the fl ame height is automatically
controlled in order to reach the set temperature.
To be able to use the day/night temperature function, the
appliance must be in the standby position.
!Caution - Always leave the remote control at the
same place, so that the thermostat is able
to ‘feel’ the room temperature;
- Make sure this place is free from infl uen-
ces such as draught, heat from radiators
and direct sunlight.
Example
By using the ✹ TEMP function you can keep the day tempe-
rature at 20 ºC; while you use the TEMP function at night
to maintain a temperature of 15 ºC.
4
Caution
Caution
… 47 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DRU GLOBAL 70 X at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DRU GLOBAL 70 X in the language / languages: English, Dutch as an attachment in your email.

The manual is 2,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info