571711

DRU GLOBAL 100 BF Manual

50
Zoom out
Zoom in
Previous page
1/64
Next page
48
USER MANUAL
4.2.5.1 Setting day/night temperature
By using the SET button, you will go through the following
functions:
MAN ✹ TEMP TEMP (P*) TIMER MAN
• Briefl y press the SET button to enter the ✹ TEMP or the
TEMP position.
• Press the SET button until the temperature on the display
fl ashes.
• Set the required temperature by using the buttons
(large fl ame) and (small fl ame).
!Caution - The minimum temperature you can set is
5 ºC / 40 ºF;
- Control of the night temperature is
switched off by lowering the temperature
until two stripes (“--”) appear on the
display.
• Press the OFF button or wait until position ✹ TEMP or
TEMP appears on the display.
4.2.5.2 Activating the thermostat function
For activating the thermostat function, you must proceed
with the following steps:
• Place the appliance in the standby (pilot burner) position
using button (small fl ame).
• Set the day/night temperature.
• Choose the ✹ TEMP or TEMP function using the SET
button.
4.2.6 Timer for thermostat function
Using the timer enables you to set two times per 24 hours
for switching on the day temperature and two times per 24
hours for switching on the night temperature.
In order to control the night temperature, it should be set
to at least 5 ºC / 40 oF.
If the night temperature is set to the “- - ” position, the
appliance will remain in the standby position. The appliance
will only switch on at the next switch-on time of the day
temperature.
The appliance must be in standby position in order to be
controlled by the timer.
Example of switch times
You have set a day temperature and night temperature of,
for example, 20 ºC and 15 ºC.
P1 ✹ TIMER = 7 hours; the temperature will go to 20 ºC
at 7 am.
P1 TIMER = 9 hours; the temperature will go to 15 ºC
at 9 am.
P2 ✹ TIMER = 17 hours; the temperature will go to 20 ºC
at 5 pm.
P2 TIMER = 22 hours; the temperature returns to 15 ºC
at 10 pm.
4.2.6.1 Setting times for the timer
To set the timer, proceed as follows:
• Set the day and night temperature as described above at
section 4.2.5.1.
• Briefl y press the SET button to enter the (P*) TIMER
position.
• Press the SET button until P1 ✹ TIMER is displayed and
the time fl ashes.
• Set the fi rst switch on time of the day temperature using
the buttons (large fl ame) and (small fl ame).
• Briefl y press the SET button to set the next time of the
cycle, P1 TIMER.
• Successively set the times P2 ✹ TIMER and P2 TIMER.
• Press the OFF button or wait until position (P*) TIMER
appears on the display.
4.2.6.2 Activating the timer function
Follow the steps below for activating the timer control:
• Place the appliance in the standby (pilot burner) position
using button (small fl ame).
• Set the day/night temperature if you have not yet done so;
for this, see section 4.2.5.1.
• Set the timer times P1 ✹ TIMER, P1 TIMER,
P2 ✹ TIMER and P2 TIMER.
• Choose the (P*) TIMER function using the SET button.
4.2.7 Replacing the battery
If the battery is almost empty, the display will show “BATT”.
To replace the battery, proceed as follows:
• Remove the cover at the back side of the remote control.
• Disconnect the 9V block battery from / connect the 9V
block battery to the connector.
!Caution - Observe the “+” and “-” poles of the
batteries and the connector;
- Use alkaline batteries;
- Batteries are regarded as “small chemical
waste” and may therefore not be
disposed with the household rubbish.
• Place the battery in the holder.
• Replace the cover.
5. Maintenance
At least once per year, the appliance should be checked for
proper and safe operation.
- Your appliance should be maintained by a
competent installer in the fi eld of
atmospheric gas-fi red heating;
- Have a cracked or broken pane replaced
immediately;
- Do not make any changes to the
appliance yourself.
Caution
… 50 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DRU GLOBAL 100 BF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DRU GLOBAL 100 BF in the language / languages: Dutch as an attachment in your email.

The manual is 2,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DRU GLOBAL 100 BF

DRU GLOBAL 100 BF User Manual - English - 20 pages

DRU GLOBAL 100 BF User Manual - German - 20 pages

DRU GLOBAL 100 BF User Manual - French - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info