571711

DRU GLOBAL 100 BF Manual

41
Zoom out
Zoom in
Previous page
1/64
Next page
English
39
INSTALLATION MANUAL
Global 100 BF
PROBLEM
A. No transmission
(motor will not run)
B. No ignition (spark)
C. No sound signal
D. One continuous sound signal
of 5 sec.
(Possible 7 short beeps prior to the
5 sec. sound signal)
POSSIBLE CAUSE
1. The (new) communication code
between receiver and remote con-
trol must still be confi rmed.
2. Empty batteries.
3. Receiver is damaged.
4. Remote control is damaged.
5. Motor cable at valve/receiver is
broken.
6. Bent pins of the 8-wire connector.
7. If the receiver is surrounded by
metal, this could decrease the trans-
mission range.
1. Button A in position MAN.
2. Ignition cable runs over and/or
alongside metal parts.
3. Ignition pen corroded.
4. 60-second delay before the full
restart is not yet fi nished.
1. Receiver is damaged.
2. 60-second delay before the full res-
tart is not yet fi nished.
1. Loose wiring between receiver and
gas control.
2. Receiver is damaged.
REMEDY
1. Hold down the reset button of the
receiver, until you hear
2 sound signals; see fi g. 20. Let go of
the reset button after the second,
longer sound signal and press
button (small fl ame) or button
(large fl ame) on the remote
control within 20 sec., until you
hear an extra long sound signal
confi rming that the new code has
been set.
2. Replace batteries.
!Caution
Avoid short circuit between the
batteries and metal parts of the
appliance.
3. Replace the receiver and confi rm
the code (remedy 1).
4. Replace the remote control and
confi rm the code (remedy 1).
5. Replace the motor cable.
6. Make sure that the pins of the
8-wire connector are straight.
7. Change the position of the antenna.
1. Switch button A on the gas control
to ON, see fi g. 16.
2 Do not place the ignition cable (S)
over and/or along metal parts. This
will weaken the spark; see fi g. 16.
If necessary, replace the ignition
cable.
3. Replace the ignition pen.
4. Wait until the delay time has
passed.
1. Replace the receiver and confi rm
the code (remedy 1 at A)
2. Wait until the delay time has
passed.
1. Connect the wiring properly.
2. Replace the receiver and confi rm
the code (remedy 1 at A)
11. Malfunctions
In the following table you will fi nd an overview of malfunctions that might occur, the possible causes and the remedies.
Table 4: Diagnosis of malfunctions
… 41 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DRU GLOBAL 100 BF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DRU GLOBAL 100 BF in the language / languages: Dutch as an attachment in your email.

The manual is 2,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DRU GLOBAL 100 BF

DRU GLOBAL 100 BF User Manual - English - 20 pages

DRU GLOBAL 100 BF User Manual - German - 20 pages

DRU GLOBAL 100 BF User Manual - French - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info