571711

DRU GLOBAL 100 BF Manual

39
Zoom out
Zoom in
Previous page
1/64
Next page
English
37
INSTALLATION MANUAL
Global 100 BF
!Caution - Make sure that the wires of
thermocouple 2 cannot come into contact
with hot parts;
- Make sure the ignition cable cannot come
into contact with other wires.
• Connect the ignition cable to the receiver;
(see fi g. 15, arrow A).
• Connect power:
a) When using batteries, see section 7.1.1 below;
b) When using an adapter:
- connect it to the receiver; (see fi g. 15, arrow C);
- insert the plug into the wall socket.
• Place the receiver (V) in the control box, as indicated on
fi g. 16.
• Bend the antenna out of the clips; see fi g. 15, arrow D.
• Set the antenna straight.
!Caution - Do not place the antenna (N) too close to
the ignition cable and/or metal parts (for
the correct position, see fi g. 16);
- Do not place the ignition cable over and/or
along metal parts: this will weaken the spark;
- Do not lay the ignition cable over the recei-
ver: this could damage the receiver;
- Avoid dust on or in the receiver: cover it
when performing work.
7.1.1 Placing / replacing the batteries
Follow the procedure below when placing the batteries:
• Open the door of the control box.
• Pick up the receiver.
• Slide the cover off.
• Place or remove the 4 penlite (AA type) batteries.
!Caution - Avoid a short circuit between the
batteries and metal objects/parts;
- Observe the “+” and “-” poles of the
batteries and the holder;
- Use alkaline batteries.
• Slide back the cover.
• Place back the receiver.
!Caution Batteries are regarded as “small chemical
waste” and may therefore not be dis-
posed with the household rubbish.
8. Final check
In order to check whether the appliance is working pro-
perly and safely, you must perform the following checks
before the appliance is used.
8.1 All connections must be gastight.
All connections must be gastight.
!Caution The gas control can be subjected to a
maximum pressure of 50 mbar.
• Check the connections for gastightness
8.2 Gas pressure / pre-pressure
The burner pressure is set at the factory; see data plate. It
is not necessary to check the burner pressure.
The pre-pressure in house installations
should be checked, as they can vary.
• Check the pre-pressure; see fi g. 17 for the measuring nipple
on the gas control.
• Contact the gas company if the pre-pressure is not correct.
8.3 Ignition pilot and main burner
For igniting the pilot and main burners, see the
User Manual, chapter 4, section 4.2, Remote Control.
- During the ignition process, you are not
allowed to operate control button B on
the gas control manually;
- Always wait 5 minutes after the pilot
burner has gone out, before you re-ignite
the appliance.
- Do not turn the pilot burner lower by
using the settings on the gas control.
8.3.1 Pilot burner
• Check the ignition of the pilot burner:
- the pilot burner should start at the fi rst attempt.
If the pilot burner does not ignite:
• check if the ignition sparks:
a) If not, the ignition cable is probably not lying free from
metal parts;
b) If it does, there is probably still air in the pipe.
• Bleed the pipe and/or
• Lay the ignition cable free from metal parts.
8.3.2 Main burner
The burner should ignite smoothly and
should not pop as a result of delayed
ignition.
• Check the function of the main burner from the standby
(pilot burner) position:
- after opening the gas valve, the main burner should burn
within a few seconds.
!Tip When the gas valve is opened, the motor
will run; this is audible.
1) If the main burner does not burn:
• Check if button A on the gas control is in the position ON;
• Check if the space surrounding the pilot burner is free
from objects;
• Check the placement of the wood set.
• If necessary, correct the above mentioned faults.
• Test the main burner 5x for a good operation.
2) If the main burner ignites, but goes out again after
approx. 22 seconds, please:
Caution
Caution
Caution
Caution
… 39 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DRU GLOBAL 100 BF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DRU GLOBAL 100 BF in the language / languages: Dutch as an attachment in your email.

The manual is 2,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DRU GLOBAL 100 BF

DRU GLOBAL 100 BF User Manual - English - 20 pages

DRU GLOBAL 100 BF User Manual - German - 20 pages

DRU GLOBAL 100 BF User Manual - French - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info