810304

DRU BASSO-01 Manual

21
Zoom out
Zoom in
Previous page
1/28
Next page
give you the information you need to install the appliance
in such a way that it will operate properly and safely.
If the installation instruction is not clear, national/local
regulations must be observed.
• NB: To ensure the ignition works properly, the ignition
wire must come into as little contact as possible with
the metal parts of the heater and should therefore
not be wound round the gas or pilot-light pipes or the
thermocouple.
• When installing the appliance, check the air circulation
(by convection) around the thermostat sensor. If there
is a lack of air circulation, the sensor must be moved
to a position with sufficient air circulation for correct
operation of the appliance.
Positioning the appliance
• The appliance should only be installed in a well ventilated
room, to ensure there will always be sufficient air supply.
• The appliance may not be installed against a wall of
combustible material unless the wall is protected with an
insulation panel.
• The connection between the pipe mouth and the flue
should be as short and straight as possible and the gas
control block easily accessible.
• The minimum distance between the back of the appliance
and the wall is 70 mm.
Connecting to the flue
• Have the chimney professionally cleaned before
connecting the appliance. Although the heater will still
work with only a very slight draught, we recommend that
the chimney be inspected for obstructions etc. annually.
• The internal diameter of the pipe mouth is 101 mm.
• The height of the pipe mouth is variable (max. 690mm,
min. 450 mm)
• Saw the plate for the outlet to the required length, as
shown in fig 3.
• Fix the outlet to the baffle using the mounting strips.
• TThe connection between the pipe mouth and the flue
duct should be made using corrosion-proof material.
• The connecting pipe should never be lower than the
heater pipe mouth.
• Fit a longer connecting pipe from the pipe mouth to the
flue sloping (2%) towards the pipe mouth.
Fitting the aluminium protective plate
The plate should be fitted under the foot of the interior
during installation. Slide the plate backwards until the front
is level with the front of the foremost adjustable feet.
Connecting to the gas supply
Use an approved connecting tap with coupling in the
supply pipe (for Belgium this must be B.G.V. approved).
In addition:
• Expel the air from the supply pipes before connecting
the appliance.
• Avoid pressure on the gas control block and the pipes.
• Check all connections for gas tightness.
Positioning the logs
• Open the glass window by unscrewing the two M6
socket-head screws on the right-hand side, using the
spanner provided.
• Place the tray around the burner (fig. 4a).
• Fill the burner with vermiculite (this is in the plastic bag
with the log set). Spread it evenly over the burner tray
and the surrounding tray. Do not put any vermiculite
higher than the edge of the tray. Save the remaining
vermiculite in case you lose any later during cleaning or
maintenance.
Position the logs as follows:
• Lay the large log (A) against the back wall, on the log
supports, with the yellow side down and the knot towards
the left.
• Lay the front logs (B and C) with the bark facing up, as
illustrated in fig. 4b.
• If appliciable and required, distribute the glow material
over the burner(s).
• Now lay the rest of the logs (D, E, F, G and H) in place as
illustrated in fig. 4b.
• Close the window again with the two socket-head screws.
The logs should not be laid in any other way as this could
cause the formation of soot. Neither should the logs
touch pilot light burner.
You can “play” with the flames by moving the vermiculite,
glow material and chips about on the burner bed until you
have created the desired flame effect.
Do not use any materials other than those supplied.
The supplied materials are incombustible and have been
manufactured specifically for this appliance.
English
INSTRUCTIONS FOR INSTALLATION
38C-2098
fig. 4a
Basso-01
19
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DRU BASSO-01 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DRU BASSO-01 in the language / languages: English, Dutch, French as an attachment in your email.

The manual is 2.08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info