488596

Dremel Trio Manual

13
Zoom out
Zoom in
Previous page
1/80
Next page
13
MAKE A FEW PRACTICE CUTS
After installing the bit into the tool and adjusting your depth
guide, you should make a few practice cuts with the tool before
attempting an actual job. A few exercises will give you the
necessary practice to make clean, professional cuts.
Step 1: Make certain that the collet nut is securely tightened
before turning the tool on.
Step 2: Hold the tool firmly and turn the tool ON to your desired
speed.
Step 3: While holding the tool firmly, insert the bit into the
material at a 45° angle, or 15° for tile (Fig. 11).
Step 4: Slowly plunge the bit to a 90° angle to begin the cut
(Fig. 12). The base guide should be flush to the material
surface. For all materials except when cutting around
outlet boxes in drywall, steer the tool in a clockwise
direction with slow, steady pressure to make the cut.
Step 5: After completing your cut, turn off the tool and carefully
remove it from the material. Do not attempt to use this
tool to make cut-outs around any fixture or opening
which has live electrical wires, or any wall which may
have live electrical wiring behind it, as the bit could
conduct current to the tool, creating an electrocution
hazard for the operator. Shut off breakers or remove
fuses to disconnect the circuit. Always hold the tool
by its thermoplastic housing, and always wear eye
protection when operating the tool.
NOTE: Because of the rotating cutting action of the bit, there will
be a slight pull when cutting. The slower you cut the more control
you have. Excessive pressure or fast cutting will cause excessive
heat and may shorten the life of the bit.
NOTE: When cutting on a vertical surface, avoid ending your cut
at the bottom of the hole. If possible, start and end your cut at
the top so the scrap part will not drop onto the rotating bit. Turn
the tool off and remove it from the material.
USING THE STRAIGHT EDGE/CIRCLE GUIDE
STRAIGHT EDGE
The straight edge guide (optional) is used for cuts parallel to the
edge of the work, and can be used from either side of the base
plate for cutting on the left or right side of the material.
1. Unscrew the base plate thumbscrew; slide the sliding rod
of the straight edge guide through the two notches on the
bottom side of the base plate.
2. Position the tool to the desired length from the edge of your
material. Tighten the thumbscrew (P) to secure the straight
edge guide to the base plate (Fig. 13).
CUTTING LARGE DIAMETER CIRCLES (10 CM DIAMETER)
1. Draw the circle on the work piece and mark the centre of the
circle. Drill a centre hole with the tracer. Make sure the edge
guide is facing UP (Fig. 14).
2. Using the tool, plunge cut a pilot hole on the edge of the circle,
turn tool off and disconnect the plug from power source.
a. To make a hole – cut from inside edge of the circle
b. To make wheels or discs – cut from the outside edge of
the circle
3. Attach straight edge guide to base plate, properly
position base onto straight edge guide to give the desired
circle diameter and lock down by tightening base plate
thumbscrew.
4. Insert plug into power source, hold the tool firmly, turn tool
on and slowly push the tool forward.
MAINTENANCE
Preventative maintenance performed by unauthorised personnel
may result in misplacing of internal wires and components which
could cause serious hazard. We recommend that all tool service
be performed by a Dremel Service Facility. To avoid injury from
unexpected starting or electrical shock, always turn off power tool
before performing service or cleaning.
CLEANING
!
WARNING
TO AVOID ACCIDENTS, ALWAYS
DISCONNECT THE TOOL AND/OR CHARGER
FROM THE POWER SUPPLY BEFORE CLEANING. The tool can be
cleaned most effectively with compressed dry air. Always wear
safety goggles when cleaning tools with compressed air.
Ventilation openings and switch levers must be kept clean
and free of foreign matter. Do not attempt to clean the tool by
inserting pointed objects through an opening.
!
WARNING
CERTAIN CLEANING AGENTS AND
SOLVENTS DAMAGE PLASTIC PARTS.
Some of these are: gasoline, carbon tetrachloride, chlorinated
cleaning solvents, ammonia and household detergents that
contain ammonia.
SERVICE AND WARRANTY
!
WARNING
NO USER SERVICEABLE PARTS INSIDE.
Preventive maintenance performed by
unauthorised personnel may result in incorrect connection of
internal wiring and components which could cause serious
hazard. We recommend that all tool service be performed by a
Dremel Service Centre. SERVICEMEN: Disconnect the tool and/or
charger from the power source before servicing.
This DREMEL product is guaranteed in accordance with statutory/
country-specific regulations; damage due to normal wear and
tear, overload or improper handling is excluded from the warranty.
In case of a complaint, send the undismantled tool or charger and
proof of purchase to your dealer.
CONTACT DREMEL
For more information on the Dremel product range, support and
hotline, go to www.dremel.com.
Dremel Europe, P.O. Box 3267, 4800 DG Breda, The Netherlands
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dremel Trio at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dremel Trio in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 1,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info