488603

Dremel Stylus Lithium -Ion Manual

10
Zoom out
Zoom in
Previous page
1/80
Next page
10
GENERAL
The Dremel multitool is a high quality precision tool that can
be used to perform detailed and intricate tasks. The wide range
of Dremel accessories and attachments allow you to perform
a large variety of tasks. These include tasks such as sanding,
carving and engraving, cutting, cleaning and polishing.
PICTURE 1
A. Collet Nut
B. Collet
C. On/Off Switch
D. Shaft Lock Button
E. Variable Speed Dial
F. Ventilation Openings
G. Softgrip
H. Charge Indicator Light
I. Charger
J. Accessory Storage
K. Wrench Storage
CHARGING THE TOOL
The Cordless Rotary Tool is not fully charged. The tool is
equipped with a non-removable battery pack. Be sure to charge
pack prior to initial use.
To charge the tool:
1. Turn tool off.
2. Place tool in the charger.
3. Plug charger into power source.
• Green light ON=charging.
• Solid green OFF=charging completed.
Charger will automatically stop charging the battery when
charging is completed. It is ok to leave tool on charger.
4. Charger will require approximately 5 hours to charge a
completely discharged battery.
IMPORTANT CHARGING NOTES
This tool has a Lithium-Ion battery and docking station offering
the following benefi ts:
1. Lithium-ion battery will hold its charge while in storage for
up to 2 years so it’s always ready when you need it.
2. You can place the tool on the charger and recharge it at any
time without reducing the original factory charge capacity.
3. The charger was designed to use as a place to store your
tool while you are working on your projects. Simply place
the tool in the charger when you’re not using it on your
project, and it will continually recharge the battery so it will
run longer.
4. The charger was designed to fast charge the battery only
when the battery temperature is between 4°C and 41°C.
5. If battery does not charge properly:
a. Check to see if tool is properly placed in charger.
b. Check for voltage at outlet by plugging in some other
electrical device.
c. Check to see if outlet is connected to a light switch
which turns power “off” when lights are turned off.
d. Check battery pack terminals for dirt. Clean with cotton
swab and alcohol if necessary.
NOTE: Use of chargers not sold by Dremel may void the
warranty.
COLLETS
The Dremel accessories available for the multitool come
with various shank sizes. Four size collets are available to
accommodate the different shank sizes. Collet sizes are
identifi ed by the rings on the back of the collet.
PICTURE 2
L. 0.8 mm Collet with one ring (483)
M. 1.6 mm Collet with two rings (482)
N. 2.4 mm Collet with three rings (481)
O. 3.2 mm Collet without ring (480)
NOTE: Some multitool kits may not include all four collet sizes.
Collets are available separately.
Always use the collet that matches the shank size of the
accessory you plan to use. Do not force a larger diameter shank
into a smaller collet.
CHANGING COLLETS
PICTURE 3
P. Shaft Lock Button
Q. Collet Wrench
R. To tighten
S. To loosen
T. Collet Nut
1. Slide the shaft lock button forward, hold down and rotate
the shaft by hand until it engages the shaft lock. Do not
engage the shaft lock button while multitool is running.
2. With the shaft lock button engaged, loosen and remove the
collet nut. Use the collet wrench if necessary.
3. Remove the collet by pulling it free from the shaft.
4. Install the appropriate size collet fully into the shaft and
reinstall the collet nut fi nger tight. Do not fully tighten the
nut when there is no bit or accessory installed.
CHANGING ACCESSORIES
PICTURE 3/4
P. Shaft Lock Button
1. Slide the shaft lock button forward, hold down and rotate
the shaft by hand until it engages the shaft lock.
2. With the shaft lock button engaged, loosen (do not remove)
the collet nut. Use the collet wrench if necessary.
3. Insert the bit or accessory shank fully into the collet.
4. With the shaft lock button engaged, fi nger tighten the collet nut
until the bit or accessory shank is gripped by the collet. Use
the collet wrench to secure the bit or accessory in the collet.
NOTE: Be sure to read the instructions supplied with your Dremel
accessory for further information on its use.
Use only Dremel tested, high performance accessories.
2610398733-CN-Stylus-0805.indb 102610398733-CN-Stylus-0805.indb 10 27-5-2008 12:12:1527-5-2008 12:12:15
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dremel Stylus Lithium -Ion at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dremel Stylus Lithium -Ion in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info