488589
10
Zoom out
Zoom in
Previous page
1/80
Next page
Model MM40
Voltage Rating: 220V-240V ~ 50/60Hz
Wattage Rating: 270W
No Load Speed: n(o) 10000-21000 min-1
Oscillation Angle, left/right: 1,5°
Weight: 1.46 kg
EXTENSION CORDS
Use completely unrolled and safe extension cords with a capacity
of 5 Amps.
ASSEMBLY
!
WARNING
ALWAYS TURN OFF THE TOOL BEFORE
CHANGING ACCESSORIES, CHANGING
COLLETS, OR SERVICING THE TOOL AND REMOVE BATTERY
PACK.
GENERAL
This Dremel Multi-Max Tool is intended for dry sanding of
surfaces, corners, edges, for scraping, for sawing soft metals,
wood and plastic components, and for grout removal using the
applicable tools and accessories recommended by Dremel.
PICTURE 1
A. On/Off switch
B. Variable speed control dial
C. Power cord
D. Ventilation openings
E. Blade washer
F. Accessory holder
G. Accessory
H. Clamping screw
PICTURE 2
A. Quick Lock™ lever
B. On/Off switch
C. Variable speed control dial
D. Power cord
E. Ventilation openings
F. Accessory holder
G. Accessory
H. Clamping flange
INSTALLING AND REMOVING ACCESSORIES
NOTE: Be sure to read the instructions supplied with your Dremel
accessory for further information on its use.
Use only Dremel tested, high performance accessories.
Dremel cutting, scraper blades have a Quick-Fit slot which allows
for faster accessory removal compared with other conventional
oscillating tool systems.
Model MM20
1. Loosen the clamping screw using the hex key provided
just enough so you can slide the accessory between the
accessory holder and the blade washer (Picture 3).
PICTURE 3
A. Accessory holder
B. Clamping screw
C. Hex key
D. Blade washer
E. Accessory
F. Accessory
G. Washer with bevel up
2. Clean accessory holder, accessory and the clamping screw
with a clean cloth.
3. Place the accessory onto the accessory holder making
sure the accessory engages all pins in the holder and the
accessory is flush against the accessory holder.
4. Securely tighten the clamping screw with the hex provided
(Picture 4).
PICTURE 4
A. Clamping screw
B. Hex key
NOTE: Some accessories, such as scrapers or blades, may be
mounted either straight on the tool, or at an angle to enhance
usability (Picture 5).
PICTURE 5
INSTALLING AND REMOVING ACCESSORIES
WITH QUICK LOCK™ ACCESSORY CHANGE
Model MM40
The Dremel Multi-Max MM40 includes an integrated accessory
change mechanism. The Quick Lock™ accessory interface allows
you to install and remove accessories without the need of a
wrench or hex key. You will also no longer need to worry about
losing a clamping screw & washer as these parts are no longer
used in the MM40 version of the Multi-Max.
1. To install an accessory using the Quick Lock™ feature, hold
tool upside down to prevent the blade from falling off the
accessory holder when installing and removing accessories.
2. Turn the Quick Lock™ lever on the top on the tool counter-
clockwise to unlock the clamping mechanism (Picture 6).
The lever needs to be fully engaged to unlock the clamping
mechanism.
PICTURE 6
A. Open
B. Close
3. Clean accessory holder, accessory and the clamping flange
with a clean cloth.
4. Place the accessory onto the accessory holder making
sure the accessory engages all pins in the holder and the
accessory is flush against the accessory holder (Picture 7 &
Picture 8).
10
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dremel Model MM40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dremel Model MM40 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 10,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info