488601

Dremel Engraver 290 Manual

6
Zoom out
Zoom in
Previous page
1/60
Next page
6
ENVIRONMENT
DISPOSAL
The machine, accessories and packaging should be so rted for 
environmental-friendly recycling.
ONLY FOR EC COUNTRIES
 Do not dispose of power tools into hous ehold waste! 
According the European Guideline 2002/96/EC for 
Waste Electrical and Electronic Equipment and its 
implementation into natio nal right, power tools that 
are no longer usable must be collected separately and 
disposed of in an  environmentally correct manner.
SPECIFICATIONS
GENERAL SPECIFICATIONS
Voltage Rating  . . . . . . . . . . . 230 V, 50-60 Hz
Amperage Rating . . . . . . . . . 0.15A
Speed . . . . . . . . . . . . . . . . . . 6000 min
-1
EXTENSION CORDS
Use completely unrolled and safe extension cords with a 
capacity of 5 Amps.
OPERATING INSTRUCTIONS
No matter how you use your Dremel electric engraver, you'll 
do a professional-like job by following these simple operating 
instructions.
1.  In order to use your engraver, you must first install the 
engraver point. To properly install the engraver point, loosen 
the set screw located in the engraver point holder (figure 1). 
Place the engraver point inside the point holder and firmly 
tighten the set screw. It is important to make sure the  engraver 
point is held firmly in place by the set screw. To remove a 
worn out engraver point, loosen the set  screw and remove the 
engraver point (figure 1). Replacement engraver points may be 
purchased from your Dremel dealer.
2.  Before plugging in the tool, be certain that the outlet voltage 
you are using matches the voltage number marked on the 
back label (name plate label) that is located on the engraver.
3.  To use the engraver, turn the engraver “ON” by moving the 
on/off switch located at the end of the tool (figure 2). Hold 
the engraver at a slight angle as you would normally hold a 
pencil. Hold the unit lightly while resting your arm comfortably 
on a table. Do not press down hard while engraving. Use a 
light touch guiding the point over the work somewhat slower 
than you would normally write.
4.  The adjusting knob on the side of the engraver housing 
controls the stroke length and therefore the depth of 
engraving (figure 3). It is not intended to be used as an “OFF” 
switch. A good “rule of thumb” is to select the  lowest setting 
which will produce a deep enough engraving mark to meet 
your requirements. To familiarize yourself, experiment with 
different settings on scrap materials. 
  NOTE: The “lowest” position of the adjusting knob will be
with the knob pointing to the number “1” on the housing.
With extended use, the positive detent indicator associated
with the depth control knob will begin to wear down and be
less noticeable. This is to be expected and does not indicate
malfunction of the engraver.
5.  The engraver point furnished with your engraver is carbide 
steel. Do not engra ve on electronic media such as CDs, 
DVDs, etc. Engravin g on these materials may damage the 
media.
SERVICE AND WARRANTY
This DREMEL product is guaranteed in accordance w ith 
statutory/cou ntry specific regulations; damage due to nor mal 
wear and tear, overload or improper handling will be excluded 
from the guarantee. 
In case of a complaint, send the tool undismantled together with 
proof of purchase to your dealer.
CONTACT DREMEL
For more i nformation on the Dremel assortment, support and 
hotline, go to www.dremel.com
Dremel Europe, P.O. Box 32 67, 4800 DG Breda, the Netherlands
ÜBERSETZUNG DER
ORIGINALBEDIENUNGSANLEITUNG
!
WARNUNG
LESEN SIE SÄMTLICHE
HINWEISE.
Fehler bei der
Einhaltung der nachstehend aufgeführten Anweisungen können
elektrischen Schlag, Brand und/ oder schwere Verletzungen
verursachen. Der nachfolgend verwendete Begriff “Elektrowerkzeug”
bezieht sich auf netzbetriebene Elektrowerkzeuge (mit Netzkabel).
BEWAHREN SIE DIESE ANWEISUNGEN
GUT AUF
1. ARBEITSPLATZ
a.   Halten Sie Ihren Arbeitsbereich sauber und aufgeräumt. 
Unordnung und unbeleuchtete Arbeitsbereiche können zu
Unfällen führen.
b.   Arbeiten Sie mit dem Gerät nicht in explosionsgefährdet er 
Umgebung, in der sich bren nbare Flüssigkeiten, Gase oder 
Stäube befinden. Elektrowerkzeuge erzeugen Funken, die
den Staub oder die Dämpfe entzünden können.
c.   Halten Sie Kinder und andere Personen während der 
Benutzung des Elektrowerkzeugs fern. Bei Ablenkung können
Sie die Kontrolle über das Gerät verlieren.
DE
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dremel Engraver 290 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dremel Engraver 290 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info