Manual Dremel Driver (page 7 of 108) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

488611

Zoom out

Zoom in

1/108

ASSEMBLY

WARNING

ALWAYS SWITCH OFF THE TOOL BEFORE

ATTACHING OR REMOVING A BIT.

GENERAL

The Dremel Cordless Screwdriver has a magnetic bit holder

that accepts any 1/4" hex bit. The low RPM capability of this

model is not a deﬁ ciency. On the contrary, low speed means

high torque and high torque is beneﬁ cial for efﬁ cient driving. The

low speed also provides more control to prevent strip-out of the

screw and damage to the work surface.

FIGURE 1

1. Magnetic bit holder

2. Ventilation openings

3. Soft grip

4. Forward/reverse lever and trigger lock

5. Variable-speed trigger switch

6. Charger

7. Charge indicator light

8. Extra storage space

9. Slot for attaching bit storage compartment

10. Bit storage compartment (optional)

GETTING STARTED

INSERTING BITS

Your power tool is equipped with a magnetic bit holder. Simply

push the shank of the bit into the bit holder as far as it will go

(Figure 2).

BIT STORAGE COMPARTMENT (optional)

Your power tool is equipped with a removable bit storage

compartment that can be attached to the charger and that will

allow you to store 12 of your favourite bits (Figure 1).

VARIABLE-SPEED TRIGGER SWITCH

Your power tool is equipped with a variable-speed trigger switch.

The power tool can be switched "ON" or "OFF" by squeezing

or releasing the trigger. The speed can be adjusted from the

minimum to maximum RPM by the pressure you apply to the

trigger. Apply more pressure to increase the speed and release

pressure to decrease speed.

BRAKE

When the trigger switch is released it activates the brake to

stop the chuck quickly. This is especially useful in the repetitive

driving and removal of screws.

AUTOLOCK

Your power tool is equipped with an automatic locking system.

This feature will lock the bit holder in one position when the

trigger switch is released. This will allow you to tighten or loosen

a nut or screw by rotating the tool by hand with the switch off.

This is convenient when higher turning torque is needed.

FORWARD/REVERSE LEVER AND TRIGGER LOCK

WARNING

AFTER TOOL USE, LOCK THE TRIGGER IN

THE "OFF" POSITION TO HELP PREVENT

ACCIDENTAL STARTS AND ACCIDENTAL DISCHARGE.

Your power tool is equipped with a forward/reverse lever and

trigger lock located above the trigger (Figure 1). This lever is

designed for changing the rotation of the bit and for locking the

trigger in an "OFF" position.

For forward rotation, (with the chuck pointed away from you)

move the lever to the far left. For reverse rotation move the lever

to the far right. To activate the trigger lock move the lever to the

centre "OFF" position.

STALL PROTECTION

This tool has a built-in stall protection feature to protect the

motor and battery in the event of a stall. If you stall the tool

for too long, or bind the bit in a work piece, especially at high

speeds, it will automatically switch itself off. Just remove the

tool from the material, switch it off for 3 seconds, then switch

it on again. When the battery is nearly discharged, the tool may

shut down automatically more frequently than normal. If this

happens, it is time to recharge the battery.

CHARGING THE TOOL

Your Dremel Driver is not completely charged at the factory. Be

sure to charge the tool prior to initial use.

To charge the tool:

1. Switch the tool off.

2. Place the tool in the charger as shown in ﬁ gure 1.

3. Plug the charger into a power source.

– Green light ON = charging.

– Green light OFF = charging completed.

The charger will automatically stop charging the battery

when charging is completed. It is OK to leave the tool on the

charger continuously.

4. The charger will require approximately 5 hours to charge a

completely discharged battery.

Important charging notes

This tool was designed with a lithium-ion battery and charger for

the following beneﬁ ts:

1. The lithium-ion battery will hold its charge while in storage for

up to 2 years. Therefore, it is always ready when you need it.

2. You can place the tool on the charger and recharge it at any

time without reducing the original charge capacity.

3. The charger was designed to use as a place to store your

tool while you are working on your projects. Simply place

the tool in the charger when you are not using it on your

project, and it will continually recharge the battery so it will

run longer for you.

4. The charger is also designed to be your permanent

storage device for your tool. Keep it on your workbench or

2610398910-Driver-0807.indb 72610398910-Driver-0807.indb 7 31-7-2008 12:37:1031-7-2008 12:37:10

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dremel Driver in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,2 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dremel Driver Manual

Product: