488595
22
Zoom out
Zoom in
Previous page
1/112
Next page
22
wires by applying excessive load to the brush. The wire
bristles can easily penetrate light clothing and/or skin.
b . If the use of a guard is recommended for wire brushing,
do not allow any interference of the wire wheel or
brush with the guard. Wire wheel or brush may expand in
diameter due to work load and centrifugal forces.
c . Do not exceed 15000min
–1
when using wire brushes.
!
WARNING
Do not work with materials containing
asbestos (asbestos is considered
carcinogenic).
!
WARNING
Take protective measures when during
work dust can develop that is harmful
to one's health, combustible or explosive (some dusts
are considered carcinogenic); wear a dust mask and
work with dust/ chip extraction when connectable.
ENVIRONMENT
DISPOSAL
The machine, accessories and packaging should be sorted for
environmental-friendly recycling.
ONLY FOR EUROPEAN COUNTRIES
Do not dispose of power tools into household waste!
According the European Guideline 2002/96/EC for
Waste Electrical and Electronic Equipment and its
implementation into national right, power tools that are
no longer usable must be collected separately and
disposed of in an environmentally correct manner.
SPECIFICATIONS
GENERAL SPECIFICATIONS
Voltage Rating . . . . . . . . . . . 10,8V
Amperage Rating . . . . . . . . . 1,3 1,5 Ah
No Load Speed . . . . . . . . . . . n
o
5000 30000min
–1
Collet Capacity . . . . . . . . . . . 0,8mm, 1,6mm, 2,4mm, 3,2mm
SPECIFICATIONS CHARGER
Input . . . . . . . . . . . . . . . . . . . 230V, 50 60Hz, 26W
Output . . . . . . . . . . . . . . . . . 3,6 V - 10,8 V
, 1,5 A
EXTENSION CORDS
Use completely unrolled and safe extension cords with a
capacity of 5 Amps.
ASSEMBLY
ALWAYS TURN OFF THE TOOL BEFORE CHANGING ACCESSORIES,
CHANGING COLLETS, OR SERVICING THE TOOL.
BATTERY CHARGE CONDITION INDICATOR
LIGHTS
Your tool is equipped with charge condition indicator lights
(picture 1 D). The indicator lights shows the charge condition of
the battery.
3 of 3 Solid LED’s = 67-100%
2 of 3 Solid LED’s = 34-66%
1 of 3 Solid LED’s = 16-33%
1 of 3 Flashing LED’s = 0-15%
3 “side to side” lights battery charge is too low to run tool.
Recharge the battery.
3 “flashing” lights battery is too hot for use. Turn tool off and
let battery cool down.
Your tool is equipped with advanced electronics that protect
the Li-Ion cells in the battery from damage due to excessive
operating temperature and/or current draw. If the warning
symbol illuminates red and/or the tool stops working during
heavy use, this most likely indicates that the Li-Ion cells are
near their maximum operating temperature, and the battery
pack should either be changed or allowed to cool to ambient
temperature before continuing use. If the tool automatically turns
off due to overload conditions, the switch must be turned off for
a few seconds to allow the circuit to reset before continuing use.
IMPORTANT CHARGING NOTES
1 . The charger was designed to fast charge the battery only
when the battery temperature is between 32°F (0°C) and
113°F (45°C). If the battery pack is too hot or too cold, the
charger will not fast charge the battery. (This may happen
if the battery pack is hot from heavy use). When the battery
temperature returns to between 32°F (0°C) and 113°F
(45°C), the charger will automatically begin charging.
2 . A substantial drop in operating time per charge may mean
that the battery pack is nearing the end of its life and
should be replaced.
3 . Remember to unplug charger during storage period.
NOTE: Use of chargers or battery packs not sold by Dremel will
void the warranty.
CHARGING BATTERY PACK (MODEL 875)
Plug charger cord into your standard power outlet.
With no battery pack inserted, the charger’s green indicator light
will go ON. This indicates the charger is receiving power and the
charger is ready for operation.
When you insert the battery pack into the charger, the charger’s
green indicator light will begin to “BLINK”. This indicates that the
battery is receiving a fast charge.
PICTURE 8
A . Battery pack
B . Charger
C . Green light
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dremel 8200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dremel 8200 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 6,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info