25143
14
Zoom out
Zoom in
Previous page
1/48
Next page
Page 14
Operating Speeds For Accessories
Set the speed indicator to fit the job to achieve the
best job results when working with different
materials.
To select the right speed for each job, use a prac-
tice piece of material. Vary speed to find the best
speed for the accessory you are using and the job
to be done.
On the Model 760, there is a LO and HI switch.
When the switch indicator is in position 1 or LO, the
tool runs at about 7,000 RPM. When the switch
indicator is in position 2 or HI, the tool runs at about
14,000 RPM.
NOTE: Speed is affected by voltage changes.
Weaker batteries with reduced voltage will slow the
RPM of the tool, especially at the lowest setting. If
your tool appears to be running more slowly than
normal, replace the batteries with fresh ones to
increase tool speed.
Most applications using the 760 Golf Club Cleaning
Tool can be accomplished using the HI speed set-
ting (position 2). The HI speed setting (position 2)
is recommended when using the 403 bristle and
535 wire brush accessories included with the tool.
LO speed is needed only for certain tasks when
more control in needed.
The speed of Model 760 is controlled by
setting this indicator on the housing.
Service
NO USER SERVICEABLE PARTS
INSIDE. Preventive mainte-
nance performed by unauthorized personnel may
result in misplacing of internal wires and compo-
nents which could cause serious hazard.
We
recommend that all tool service be performed by a
Dremel Service Facility.
D.C. motors
The motor in your tool has been engineered for
many hours of dependable service. To maintain peak
efficiency of the motor, we recommend it be exam-
ined every six months. Only a genuine Dremel
replacement motor specially designed for your tool
should be used.
Cleaning
To avoid accidents, always dis-
connect battery pack before
cleaning.
The tool may be cleaned most effectively
with compressed dry air.
Always wear safety gog-
gles when cleaning tools with compressed air.
Ventilation openings and switch levers must be kept
clean and free of foreign matter. Do not attempt to
clean by inserting pointed objects through opening.
Certain cleaning agents and sol-
vents damage plastic parts.
Some of these are: gasoline, carbon tetrachloride,
chlorinated cleaning solvents, ammonia and house-
hold detergents that contain ammonia.
!
WARNING
Maintenance
!
WARNING
!
CAUTION
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dremel 760 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dremel 760 in the language / languages: English, Spanish as an attachment in your email.

The manual is 5,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info